diff --git a/src/arm/broadcom/bcm-cygnus-clock.dtsi b/src/arm/broadcom/bcm-cygnus-clock.dtsi
new file mode 100644
index 0000000..52f91a1
--- /dev/null
+++ b/src/arm/broadcom/bcm-cygnus-clock.dtsi
@@ -0,0 +1,133 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2014 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+clocks {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	osc: oscillator {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <25000000>;
+	};
+
+	/* Cygnus ARM PLL */
+	armpll: armpll@19000000 {
+		#clock-cells = <0>;
+		compatible = "brcm,cygnus-armpll";
+		clocks = <&osc>;
+		reg = <0x19000000 0x1000>;
+	};
+
+	/* peripheral clock for system timer */
+	periph_clk: arm_periph_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&armpll>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	/* APB bus clock */
+	apb_clk: apb_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&armpll>;
+		clock-div = <4>;
+		clock-mult = <1>;
+	};
+
+	genpll: genpll@301d000 {
+		#clock-cells = <1>;
+		compatible = "brcm,cygnus-genpll";
+		reg = <0x0301d000 0x2c>, <0x0301c020 0x4>;
+		clocks = <&osc>;
+		clock-output-names = "genpll", "axi21", "250mhz", "ihost_sys",
+				     "enet_sw", "audio_125", "can";
+	};
+
+	/* always 1/2 of the axi21 clock */
+	axi41_clk: axi41_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&genpll 1>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	/* always 1/4 of the axi21 clock */
+	axi81_clk: axi81_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&genpll 1>;
+		clock-div = <4>;
+		clock-mult = <1>;
+	};
+
+	lcpll0: lcpll0@301d02c {
+		#clock-cells = <1>;
+		compatible = "brcm,cygnus-lcpll0";
+		reg = <0x0301d02c 0x1c>, <0x0301c020 0x4>;
+		clocks = <&osc>;
+		clock-output-names = "lcpll0", "pcie_phy", "ddr_phy", "sdio",
+				     "usb_phy", "smart_card", "ch5";
+	};
+
+	mipipll: mipipll@180a9800 {
+		#clock-cells = <1>;
+		compatible = "brcm,cygnus-mipipll";
+		reg = <0x180a9800 0x2c>, <0x0301c020 0x4>, <0x180aa024 0x4>;
+		clocks = <&osc>;
+		clock-output-names = "mipipll", "ch0_unused", "ch1_lcd",
+				     "ch2_v3d", "ch3_unused", "ch4_unused",
+				     "ch5_unused";
+	};
+
+	asiu_clks: asiu_clks@301d048 {
+		#clock-cells = <1>;
+		compatible = "brcm,cygnus-asiu-clk";
+		reg = <0x0301d048 0xc>, <0x180aa024 0x4>;
+
+		clocks = <&osc>;
+		clock-output-names = "keypad", "adc/touch", "pwm";
+	};
+
+	audiopll: audiopll@180aeb00 {
+		#clock-cells = <1>;
+		compatible = "brcm,cygnus-audiopll";
+		reg = <0x180aeb00 0x68>;
+		clocks = <&osc>;
+		clock-output-names = "audiopll", "ch0_audio",
+					"ch1_audio", "ch2_audio";
+	};
+};
diff --git a/src/arm/broadcom/bcm-cygnus.dtsi b/src/arm/broadcom/bcm-cygnus.dtsi
new file mode 100644
index 0000000..f9f79ed
--- /dev/null
+++ b/src/arm/broadcom/bcm-cygnus.dtsi
@@ -0,0 +1,623 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2014 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/clock/bcm-cygnus.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,cygnus";
+	model = "Broadcom Cygnus SoC";
+	interrupt-parent = <&gic>;
+
+	aliases {
+		ethernet0 = &eth0;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			reg = <0x0>;
+		};
+	};
+
+	/include/ "bcm-cygnus-clock.dtsi"
+
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	core@19000000 {
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x19000000 0x1000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		timer@20200 {
+			compatible = "arm,cortex-a9-global-timer";
+			reg = <0x20200 0x100>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&periph_clk>;
+		};
+
+		gic: interrupt-controller@21000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x21000 0x1000>,
+			      <0x20100 0x100>;
+		};
+
+		L2: cache-controller@22000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x22000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+		};
+	};
+
+	axi {
+		compatible = "simple-bus";
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		otp: otp@301c800 {
+			compatible = "brcm,ocotp";
+			reg = <0x0301c800 0x2c>;
+			brcm,ocotp-size = <2048>;
+			status = "disabled";
+		};
+
+		pcie_phy: pcie_phy@301d0a0 {
+			compatible = "brcm,cygnus-pcie-phy";
+			reg = <0x0301d0a0 0x14>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pcie0_phy: pcie-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+
+			pcie1_phy: pcie-phy@1 {
+				reg = <1>;
+				#phy-cells = <0>;
+			};
+		};
+
+		pinctrl: pinctrl@301d0c8 {
+			compatible = "brcm,cygnus-pinmux";
+			reg = <0x0301d0c8 0x30>,
+			      <0x0301d24c 0x2c>;
+
+			spi_0: spi_0 {
+				function = "spi0";
+				groups = "spi0_grp";
+			};
+
+			spi_1: spi_1 {
+				function = "spi1";
+				groups = "spi1_grp";
+			};
+
+			spi_2: spi_2 {
+				function = "spi2";
+				groups = "spi2_grp";
+			};
+		};
+
+		mailbox: mailbox@3024024 {
+			compatible = "brcm,iproc-mailbox";
+			reg = <0x03024024 0x40>;
+			interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			#mbox-cells = <1>;
+		};
+
+		gpio_crmu: gpio@3024800 {
+			compatible = "brcm,cygnus-crmu-gpio";
+			reg = <0x03024800 0x50>,
+			      <0x03024008 0x18>;
+			ngpios = <6>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&mailbox>;
+			interrupts = <0>;
+		};
+
+		mdio: mdio@18002000 {
+			compatible = "brcm,iproc-mdio";
+			reg = <0x18002000 0x8>;
+			#size-cells = <0>;
+			#address-cells = <1>;
+			status = "disabled";
+
+			gphy0: ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			gphy1: ethernet-phy@1 {
+				reg = <1>;
+			};
+		};
+
+		switch: switch@18007000 {
+			compatible = "brcm,bcm11360-srab", "brcm,cygnus-srab";
+			reg = <0x18007000 0x1000>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					phy-handle = <&gphy0>;
+					phy-mode = "rgmii";
+				};
+
+				port@1 {
+					reg = <1>;
+					phy-handle = <&gphy1>;
+					phy-mode = "rgmii";
+				};
+
+				port@8 {
+					reg = <8>;
+					label = "cpu";
+					ethernet = <&eth0>;
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+			};
+		};
+
+		i2c0: i2c@18008000 {
+			compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+			reg = <0x18008000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <100000>;
+			status = "disabled";
+		};
+
+		wdt0: wdt@18009000 {
+			compatible = "arm,sp805" , "arm,primecell";
+			reg = <0x18009000 0x1000>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "wdog_clk", "apb_pclk";
+		};
+
+		gpio_ccm: gpio@1800a000 {
+			compatible = "brcm,cygnus-ccm-gpio";
+			reg = <0x1800a000 0x50>,
+			      <0x0301d164 0x20>;
+			ngpios = <24>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+		};
+
+		i2c1: i2c@1800b000 {
+			compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+			reg = <0x1800b000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <100000>;
+			status = "disabled";
+		};
+
+		pcie0: pcie@18012000 {
+			compatible = "brcm,iproc-pcie";
+			reg = <0x18012000 0x1000>;
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+
+			linux,pci-domain = <0>;
+
+			bus-range = <0x00 0xff>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x81000000 0 0	  0x28000000 0 0x00010000>,
+				 <0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
+
+			phys = <&pcie0_phy>;
+			phy-names = "pcie-phy";
+
+			status = "disabled";
+
+			msi-parent = <&msi0>;
+			msi0: msi {
+				compatible = "brcm,iproc-msi";
+				msi-controller;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		pcie1: pcie@18013000 {
+			compatible = "brcm,iproc-pcie";
+			reg = <0x18013000 0x1000>;
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+
+			linux,pci-domain = <1>;
+
+			bus-range = <0x00 0xff>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x81000000 0 0	  0x48000000 0 0x00010000>,
+				 <0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
+
+			phys = <&pcie1_phy>;
+			phy-names = "pcie-phy";
+
+			status = "disabled";
+
+			msi-parent = <&msi1>;
+			msi1: msi {
+				compatible = "brcm,iproc-msi";
+				msi-controller;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		dma0: dma@18018000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x18018000 0x1000>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&apb_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
+
+		uart0: serial@18020000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x18020000 0x100>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&axi81_clk>;
+			clock-frequency = <100000000>;
+			status = "disabled";
+		};
+
+		uart1: serial@18021000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x18021000 0x100>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&axi81_clk>;
+			clock-frequency = <100000000>;
+			status = "disabled";
+		};
+
+		uart2: serial@18022000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x18022000 0x100>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&axi81_clk>;
+			clock-frequency = <100000000>;
+			status = "disabled";
+		};
+
+		uart3: serial@18023000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x18023000 0x100>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&axi81_clk>;
+			clock-frequency = <100000000>;
+			status = "disabled";
+		};
+
+		spi0: spi@18028000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x18028000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-0 = <&spi_0>;
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "sspclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		spi1: spi@18029000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x18029000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-0 = <&spi_1>;
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "sspclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		spi2: spi@1802a000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x1802a000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-0 = <&spi_2>;
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "sspclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		rng: rng@18032000 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0x18032000 0x28>;
+		};
+
+		sdhci0: sdhci@18041000 {
+			compatible = "brcm,sdhci-iproc-cygnus";
+			reg = <0x18041000 0x100>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&lcpll0 BCM_CYGNUS_LCPLL0_SDIO_CLK>;
+			bus-width = <4>;
+			sdhci,auto-cmd12;
+			status = "disabled";
+		};
+
+		eth0: ethernet@18042000 {
+			compatible = "brcm,amac";
+			reg = <0x18042000 0x1000>,
+			      <0x18110000 0x1000>;
+			reg-names = "amac_base", "idm_base";
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		sdhci1: sdhci@18043000 {
+			compatible = "brcm,sdhci-iproc-cygnus";
+			reg = <0x18043000 0x100>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&lcpll0 BCM_CYGNUS_LCPLL0_SDIO_CLK>;
+			bus-width = <4>;
+			sdhci,auto-cmd12;
+			status = "disabled";
+		};
+
+		nand_controller: nand-controller@18046000 {
+			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
+			reg = <0x18046000 0x600>, <0xf8105408 0x600>,
+			      <0x18046f00 0x20>;
+			reg-names = "nand", "iproc-idm", "iproc-ext";
+			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			brcm,nand-has-wp;
+		};
+
+		ehci0: usb@18048000 {
+			compatible = "generic-ehci";
+			reg = <0x18048000 0x100>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		ohci0: usb@18048800 {
+			compatible = "generic-ohci";
+			reg = <0x18048800 0x100>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		clcd: clcd@180a0000 {
+			compatible = "arm,pl111", "arm,primecell";
+			reg = <0x180a0000 0x1000>;
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "combined";
+			clocks = <&axi41_clk>, <&apb_clk>;
+			clock-names = "clcdclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		v3d: v3d@180a2000 {
+			compatible = "brcm,cygnus-v3d";
+			reg = <0x180a2000 0x1000>;
+			clocks = <&mipipll BCM_CYGNUS_MIPIPLL_CH2_V3D>;
+			clock-names = "v3d_clk";
+			interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		vc4: gpu {
+			compatible = "brcm,cygnus-vc4";
+		};
+
+		gpio_asiu: gpio@180a5000 {
+			compatible = "brcm,cygnus-asiu-gpio";
+			reg = <0x180a5000 0x668>;
+			ngpios = <146>;
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			interrupt-controller;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-ranges = <&pinctrl 0 42 1>,
+					<&pinctrl 1 44 3>,
+					<&pinctrl 4 48 1>,
+					<&pinctrl 5 50 3>,
+					<&pinctrl 8 126 1>,
+					<&pinctrl 9 155 1>,
+					<&pinctrl 10 152 1>,
+					<&pinctrl 11 154 1>,
+					<&pinctrl 12 153 1>,
+					<&pinctrl 13 127 3>,
+					<&pinctrl 16 140 1>,
+					<&pinctrl 17 145 7>,
+					<&pinctrl 24 130 10>,
+					<&pinctrl 34 141 4>,
+					<&pinctrl 38 54 1>,
+					<&pinctrl 39 56 3>,
+					<&pinctrl 42 60 3>,
+					<&pinctrl 45 64 3>,
+					<&pinctrl 48 68 2>,
+					<&pinctrl 50 84 6>,
+					<&pinctrl 56 94 6>,
+					<&pinctrl 62 72 1>,
+					<&pinctrl 63 70 1>,
+					<&pinctrl 64 80 1>,
+					<&pinctrl 65 74 3>,
+					<&pinctrl 68 78 1>,
+					<&pinctrl 69 82 1>,
+					<&pinctrl 70 156 17>,
+					<&pinctrl 87 104 12>,
+					<&pinctrl 99 102 2>,
+					<&pinctrl 101 90 4>,
+					<&pinctrl 105 116 6>,
+					<&pinctrl 111 100 2>,
+					<&pinctrl 113 122 4>,
+					<&pinctrl 123 11 1>,
+					<&pinctrl 124 38 4>,
+					<&pinctrl 128 43 1>,
+					<&pinctrl 129 47 1>,
+					<&pinctrl 130 49 1>,
+					<&pinctrl 131 53 1>,
+					<&pinctrl 132 55 1>,
+					<&pinctrl 133 59 1>,
+					<&pinctrl 134 63 1>,
+					<&pinctrl 135 67 1>,
+					<&pinctrl 136 71 1>,
+					<&pinctrl 137 73 1>,
+					<&pinctrl 138 77 1>,
+					<&pinctrl 139 79 1>,
+					<&pinctrl 140 81 1>,
+					<&pinctrl 141 83 1>,
+					<&pinctrl 142 10 1>;
+		};
+
+		ts_adc_syscon: ts_adc_syscon@180a6000 {
+			compatible = "brcm,iproc-ts-adc-syscon", "syscon";
+			reg = <0x180a6000 0xc30>;
+		};
+
+		touchscreen: touchscreen@180a6000 {
+			compatible = "brcm,iproc-touchscreen";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ts_syscon = <&ts_adc_syscon>;
+			clocks = <&asiu_clks BCM_CYGNUS_ASIU_ADC_CLK>;
+			clock-names = "tsc_clk";
+			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		adc: adc@180a6000 {
+			compatible = "brcm,iproc-static-adc";
+			#io-channel-cells = <1>;
+			adc-syscon = <&ts_adc_syscon>;
+			clocks = <&asiu_clks BCM_CYGNUS_ASIU_ADC_CLK>;
+			clock-names = "tsc_clk";
+			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		pwm: pwm@180aa500 {
+			compatible = "brcm,kona-pwm";
+			reg = <0x180aa500 0xc4>;
+			#pwm-cells = <3>;
+			clocks = <&asiu_clks BCM_CYGNUS_ASIU_PWM_CLK>;
+			status = "disabled";
+		};
+
+		keypad: keypad@180ac000 {
+			compatible = "brcm,bcm-keypad";
+			reg = <0x180ac000 0x14c>;
+			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&asiu_clks BCM_CYGNUS_ASIU_KEYPAD_CLK>;
+			clock-names = "peri_clk";
+			clock-frequency = <31250>;
+			pull-up-enabled;
+			col-debounce-filter-period = <0>;
+			status-debounce-filter-period = <0>;
+			row-output-enabled;
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm-hr2.dtsi b/src/arm/broadcom/bcm-hr2.dtsi
new file mode 100644
index 0000000..788a680
--- /dev/null
+++ b/src/arm/broadcom/bcm-hr2.dtsi
@@ -0,0 +1,368 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2017 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,hr2";
+	model = "Broadcom Hurricane 2 SoC";
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			reg = <0x0>;
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>;
+	};
+
+	mpcore@19000000 {
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x19000000 0x00023000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		a9pll: arm_clk@0 {
+			#clock-cells = <0>;
+			compatible = "brcm,hr2-armpll";
+			clocks = <&osc>;
+			reg = <0x0 0x1000>;
+		};
+
+		timer@20200 {
+			compatible = "arm,cortex-a9-global-timer";
+			reg = <0x20200 0x100>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&periph_clk>;
+		};
+
+		twd-timer@20600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0x20600 0x20>;
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) |
+						  IRQ_TYPE_EDGE_RISING)>;
+			clocks = <&periph_clk>;
+		};
+
+		twd-watchdog@20620 {
+			compatible = "arm,cortex-a9-twd-wdt";
+			reg = <0x20620 0x20>;
+			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) |
+						  IRQ_TYPE_EDGE_RISING)>;
+			clocks = <&periph_clk>;
+		};
+
+		gic: interrupt-controller@21000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x21000 0x1000>,
+			      <0x20100 0x100>;
+		};
+
+		L2: cache-controller@22000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x22000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+		};
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc: oscillator {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <25000000>;
+		};
+
+		periph_clk: periph_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&a9pll>;
+			clock-div = <2>;
+			clock-mult = <1>;
+		};
+	};
+
+	axi@18000000 {
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x18000000 0x0011c40c>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		uart0: serial@300 {
+			compatible = "ns16550a";
+			reg = <0x0300 0x100>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc>;
+			status = "disabled";
+		};
+
+		uart1: serial@400 {
+			compatible = "ns16550a";
+			reg = <0x0400 0x100>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc>;
+			status = "disabled";
+		};
+
+		dma@20000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x20000 0x1000>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			status = "disabled";
+		};
+
+		amac0: ethernet@22000 {
+			compatible = "brcm,nsp-amac";
+			reg = <0x22000 0x1000>,
+			      <0x110000 0x1000>;
+			reg-names = "amac_base", "idm_base";
+			interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		nand_controller: nand-controller@26000 {
+			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
+			reg = <0x26000 0x600>,
+			      <0x11b408 0x600>,
+			      <0x026f00 0x20>;
+			reg-names = "nand", "iproc-idm", "iproc-ext";
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			brcm,nand-has-wp;
+		};
+
+		gpiob: gpio@30000 {
+			compatible = "brcm,iproc-hr2-gpio", "brcm,iproc-gpio";
+			reg = <0x30000 0x50>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			ngpios = <4>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pwm: pwm@31000 {
+			compatible = "brcm,iproc-pwm";
+			reg = <0x31000 0x28>;
+			clocks = <&osc>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		rng: rng@33000 {
+			compatible = "brcm,bcm-nsp-rng";
+			reg = <0x33000 0x14>;
+		};
+
+		qspi: spi@27200 {
+			compatible = "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi";
+			reg = <0x027200 0x184>,
+			      <0x027000 0x124>,
+			      <0x11c408 0x004>,
+			      <0x0273a0 0x01c>;
+			reg-names = "mspi", "bspi", "intr_regs",
+				    "intr_status_reg";
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "spi_lr_fullness_reached",
+					  "spi_lr_session_aborted",
+					  "spi_lr_impatient",
+					  "spi_lr_session_done",
+					  "spi_lr_overhead",
+					  "mspi_done",
+					  "mspi_halted";
+			num-cs = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* partitions defined in board DTS */
+		};
+
+		ccbtimer0: timer@34000 {
+			compatible = "arm,sp804";
+			reg = <0x34000 0x1000>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		ccbtimer1: timer@35000 {
+			compatible = "arm,sp804";
+			reg = <0x35000 0x1000>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		i2c0: i2c@38000 {
+			compatible = "brcm,iproc-i2c";
+			reg = <0x38000 0x50>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <100000>;
+		};
+
+		watchdog: watchdog@39000 {
+			compatible = "arm,sp805", "arm,primecell";
+			reg = <0x39000 0x1000>;
+			interrupts = <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		i2c1: i2c@3b000 {
+			compatible = "brcm,iproc-i2c";
+			reg = <0x3b000 0x50>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <100000>;
+		};
+	};
+
+	pflash: nor@20000000 {
+		compatible = "cfi-flash", "jedec-flash";
+		reg = <0x20000000 0x04000000>;
+		status = "disabled";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* partitions defined in board DTS */
+	};
+
+	pcie0: pcie@18012000 {
+		compatible = "brcm,iproc-pcie";
+		reg = <0x18012000 0x1000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+
+		linux,pci-domain = <0>;
+
+		bus-range = <0x00 0xff>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+
+		/* Note: The HW does not support I/O resources.  So,
+		 * only the memory resource range is being specified.
+		 */
+		ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
+
+		status = "disabled";
+
+		msi-parent = <&msi0>;
+		msi0: msi {
+			compatible = "brcm,iproc-msi";
+			msi-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
+			brcm,pcie-msi-inten;
+		};
+	};
+
+	pcie1: pcie@18013000 {
+		compatible = "brcm,iproc-pcie";
+		reg = <0x18013000 0x1000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+
+		linux,pci-domain = <1>;
+
+		bus-range = <0x00 0xff>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+
+		/* Note: The HW does not support I/O resources.  So,
+		 * only the memory resource range is being specified.
+		 */
+		ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
+
+		status = "disabled";
+
+		msi-parent = <&msi1>;
+		msi1: msi {
+			compatible = "brcm,iproc-msi";
+			msi-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
+			brcm,pcie-msi-inten;
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm-ns.dtsi b/src/arm/broadcom/bcm-ns.dtsi
new file mode 100644
index 0000000..d0d5f7e
--- /dev/null
+++ b/src/arm/broadcom/bcm-ns.dtsi
@@ -0,0 +1,516 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2013-2014 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+#include <dt-bindings/clock/bcm-nsp.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts =
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	chipcommon-a-bus@18000000 {
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x18000000 0x00001000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		uart0: serial@300 {
+			compatible = "ns16550";
+			reg = <0x0300 0x100>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&iprocslow>;
+			status = "disabled";
+		};
+
+		uart1: serial@400 {
+			compatible = "ns16550";
+			reg = <0x0400 0x100>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&iprocslow>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinmux_uart1>;
+			status = "disabled";
+		};
+	};
+
+	mpcore-bus@19000000 {
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x19000000 0x00023000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		scu@20000 {
+			compatible = "arm,cortex-a9-scu";
+			reg = <0x20000 0x100>;
+		};
+
+		timer@20200 {
+			compatible = "arm,cortex-a9-global-timer";
+			reg = <0x20200 0x100>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&periph_clk>;
+		};
+
+		timer@20600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0x20600 0x20>;
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
+						  IRQ_TYPE_EDGE_RISING)>;
+			clocks = <&periph_clk>;
+		};
+
+		gic: interrupt-controller@21000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x21000 0x1000>,
+			      <0x20100 0x100>;
+		};
+
+		L2: cache-controller@22000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x22000 0x1000>;
+			cache-unified;
+			arm,shared-override;
+			prefetch-data = <1>;
+			prefetch-instr = <1>;
+			cache-level = <2>;
+		};
+	};
+
+	axi@18000000 {
+		compatible = "brcm,bus-axi";
+		reg = <0x18000000 0x1000>;
+		ranges = <0x00000000 0x18000000 0x00100000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0x000fffff 0xffff>;
+		interrupt-map =
+			/* ChipCommon */
+			<0x00000000 0 &gic GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* Switch Register Access Block */
+			<0x00007000 0 &gic GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00007000 1 &gic GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00007000 2 &gic GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00007000 3 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00007000 4 &gic GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00007000 5 &gic GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00007000 6 &gic GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00007000 7 &gic GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00007000 8 &gic GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00007000 9 &gic GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00007000 10 &gic GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00007000 11 &gic GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00007000 12 &gic GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* PCIe Controller 0 */
+			<0x00012000 0 &gic GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00012000 1 &gic GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00012000 2 &gic GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00012000 3 &gic GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00012000 4 &gic GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00012000 5 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* PCIe Controller 1 */
+			<0x00013000 0 &gic GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00013000 1 &gic GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00013000 2 &gic GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00013000 3 &gic GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00013000 4 &gic GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00013000 5 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* PCIe Controller 2 */
+			<0x00014000 0 &gic GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00014000 1 &gic GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00014000 2 &gic GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00014000 3 &gic GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00014000 4 &gic GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00014000 5 &gic GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* USB 2.0 Controller */
+			<0x00021000 0 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* USB 3.0 Controller */
+			<0x00023000 0 &gic GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* Ethernet Controller 0 */
+			<0x00024000 0 &gic GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* Ethernet Controller 1 */
+			<0x00025000 0 &gic GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* Ethernet Controller 2 */
+			<0x00026000 0 &gic GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* Ethernet Controller 3 */
+			<0x00027000 0 &gic GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* NAND Controller */
+			<0x00028000 0 &gic GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 1 &gic GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 2 &gic GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 3 &gic GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 4 &gic GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 5 &gic GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 6 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 7 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+
+		chipcommon: chipcommon@0 {
+			reg = <0x00000000 0x1000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pcie0: pcie@12000 {
+			reg = <0x00012000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+		};
+
+		pcie1: pcie@13000 {
+			reg = <0x00013000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+		};
+
+		pcie2: pcie@14000 {
+			reg = <0x00014000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+		};
+
+		usb2: usb2@21000 {
+			reg = <0x00021000 0x1000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			interrupt-parent = <&gic>;
+
+			ehci: usb@21000 {
+				compatible = "generic-ehci";
+				reg = <0x00021000 0x1000>;
+				interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&usb2_phy>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ehci_port1: port@1 {
+					reg = <1>;
+					#trigger-source-cells = <0>;
+				};
+
+				ehci_port2: port@2 {
+					reg = <2>;
+					#trigger-source-cells = <0>;
+				};
+			};
+
+			ohci: usb@22000 {
+				compatible = "generic-ohci";
+				reg = <0x00022000 0x1000>;
+				interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ohci_port1: port@1 {
+					reg = <1>;
+					#trigger-source-cells = <0>;
+				};
+
+				ohci_port2: port@2 {
+					reg = <2>;
+					#trigger-source-cells = <0>;
+				};
+			};
+		};
+
+		usb3: usb3@23000 {
+			reg = <0x00023000 0x1000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			interrupt-parent = <&gic>;
+
+			xhci: usb@23000 {
+				compatible = "generic-xhci";
+				reg = <0x00023000 0x1000>;
+				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&usb3_phy>;
+				phy-names = "usb";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				xhci_port1: port@1 {
+					reg = <1>;
+					#trigger-source-cells = <0>;
+				};
+			};
+		};
+
+		gmac0: ethernet@24000 {
+			reg = <0x24000 0x800>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac1: ethernet@25000 {
+			reg = <0x25000 0x800>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac2: ethernet@26000 {
+			reg = <0x26000 0x800>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac3: ethernet@27000 {
+			reg = <0x27000 0x800>;
+		};
+	};
+
+	pwm: pwm@18002000 {
+		compatible = "brcm,iproc-pwm";
+		reg = <0x18002000 0x28>;
+		clocks = <&osc>;
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	mdio: mdio@18003000 {
+		compatible = "brcm,iproc-mdio";
+		reg = <0x18003000 0x8>;
+		#size-cells = <0>;
+		#address-cells = <1>;
+	};
+
+	mdio-mux@18003000 {
+		compatible = "mdio-mux-mmioreg", "mdio-mux";
+		mdio-parent-bus = <&mdio>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x18003000 0x4>;
+		mux-mask = <0x200>;
+
+		mdio@0 {
+			reg = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			usb3_phy: usb3-phy@10 {
+				compatible = "brcm,ns-ax-usb3-phy";
+				reg = <0x10>;
+				usb3-dmp-syscon = <&usb3_dmp>;
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
+	};
+
+	rng: rng@18004000 {
+		compatible = "brcm,bcm5301x-rng";
+		reg = <0x18004000 0x14>;
+	};
+
+	srab: ethernet-switch@18007000 {
+		compatible = "brcm,bcm53011-srab", "brcm,bcm5301x-srab";
+		reg = <0x18007000 0x1000>;
+
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+			};
+
+			port@1 {
+				reg = <1>;
+			};
+
+			port@2 {
+				reg = <2>;
+			};
+
+			port@3 {
+				reg = <3>;
+			};
+
+			port@4 {
+				reg = <4>;
+			};
+
+			port@5 {
+				reg = <5>;
+				ethernet = <&gmac0>;
+			};
+
+			port@7 {
+				reg = <7>;
+				ethernet = <&gmac1>;
+			};
+
+			port@8 {
+				reg = <8>;
+				ethernet = <&gmac2>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+
+	uart2: serial@18008000 {
+		compatible = "ns16550a";
+		reg = <0x18008000 0x20>;
+		clocks = <&iprocslow>;
+		interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	dmu-bus@1800c000 {
+		compatible = "simple-bus";
+		ranges = <0 0x1800c000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		cru-bus@100 {
+			compatible = "brcm,ns-cru", "simple-mfd";
+			reg = <0x100 0x1a4>;
+			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			usb2_phy: phy@164 {
+				compatible = "brcm,ns-usb2-phy";
+				reg = <0x164 0x4>;
+				brcm,syscon-clkset = <&cru_clkset>;
+				clocks = <&genpll BCM_NSP_GENPLL_USB_PHY_REF_CLK>;
+				clock-names = "phy-ref-clk";
+				#phy-cells = <0>;
+			};
+
+			cru_clkset: syscon@180 {
+				compatible = "brcm,cru-clkset", "syscon";
+				reg = <0x180 0x4>;
+			};
+
+			pinctrl: pinctrl@1c0 {
+				compatible = "brcm,bcm4708-pinmux";
+				reg = <0x1c0 0x24>;
+				reg-names = "cru_gpio_control";
+
+				spi-pins {
+					groups = "spi_grp";
+					function = "spi";
+				};
+
+				pinmux_i2c: i2c-pins {
+					groups = "i2c_grp";
+					function = "i2c";
+				};
+
+				pinmux_pwm: pwm-pins {
+					groups = "pwm0_grp", "pwm1_grp",
+						 "pwm2_grp", "pwm3_grp";
+					function = "pwm";
+				};
+
+				pinmux_uart1: uart1-pins {
+					groups = "uart1_grp";
+					function = "uart1";
+				};
+			};
+
+			thermal: thermal@2c0 {
+				compatible = "brcm,ns-thermal";
+				reg = <0x2c0 0x10>;
+				#thermal-sensor-cells = <0>;
+			};
+		};
+	};
+
+	nand_controller: nand-controller@18028000 {
+		compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand";
+		reg = <0x18028000 0x600>, <0x1811a408 0x600>, <0x18028f00 0x20>;
+		reg-names = "nand", "iproc-idm", "iproc-ext";
+		interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		brcm,nand-has-wp;
+	};
+
+	usb3_dmp: syscon@18105000 {
+		reg = <0x18105000 0x1000>;
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+			coefficients = <(-556) 418000>;
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+			};
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm-nsp-ax.dtsi b/src/arm/broadcom/bcm-nsp-ax.dtsi
new file mode 100644
index 0000000..f2e941d
--- /dev/null
+++ b/src/arm/broadcom/bcm-nsp-ax.dtsi
@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom Northstar Plus Ax stepping-specific bindings.
+ * Notable differences from B0+ are the secondary-boot-reg and
+ * lack of DMA coherency.
+ */
+
+&cpu1 {
+	secondary-boot-reg = <0xffff042c>;
+};
+
+&dma {
+	/delete-property/ dma-coherent;
+};
+
+&sdio {
+	/delete-property/ dma-coherent;
+};
+
+&amac0 {
+	/delete-property/ dma-coherent;
+};
+
+&amac1 {
+	/delete-property/ dma-coherent;
+};
+
+&amac2 {
+	/delete-property/ dma-coherent;
+};
+
+&ehci0 {
+	/delete-property/ dma-coherent;
+};
+
+&mailbox {
+	/delete-property/ dma-coherent;
+};
+
+&xhci {
+	/delete-property/ dma-coherent;
+};
+
+&ehci0 {
+	/delete-property/ dma-coherent;
+};
+
+&ohci0 {
+	/delete-property/ dma-coherent;
+};
+
+&i2c0 {
+	/delete-property/ dma-coherent;
+};
+
+&sata {
+	/delete-property/ dma-coherent;
+};
+
+&pcie0 {
+	/delete-property/ dma-coherent;
+};
+
+&pcie1 {
+	/delete-property/ dma-coherent;
+};
+
+&pcie2 {
+	/delete-property/ dma-coherent;
+};
diff --git a/src/arm/broadcom/bcm-nsp.dtsi b/src/arm/broadcom/bcm-nsp.dtsi
new file mode 100644
index 0000000..9d20ba3
--- /dev/null
+++ b/src/arm/broadcom/bcm-nsp.dtsi
@@ -0,0 +1,695 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2015 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/clock/bcm-nsp.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,nsp";
+	model = "Broadcom Northstar Plus SoC";
+	interrupt-parent = <&gic>;
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		ethernet0 = &amac0;
+		ethernet1 = &amac1;
+		ethernet2 = &amac2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			reg = <0x0>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			enable-method = "brcm,bcm-nsp-smp";
+			secondary-boot-reg = <0xffff0fec>;
+			reg = <0x1>;
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+
+	mpcore-bus@19000000 {
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x19000000 0x00023000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		a9pll: arm_clk@0 {
+			#clock-cells = <0>;
+			compatible = "brcm,nsp-armpll";
+			clocks = <&osc>;
+			reg = <0x00000 0x1000>;
+		};
+
+		timer@20200 {
+			compatible = "arm,cortex-a9-global-timer";
+			reg = <0x20200 0x100>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&periph_clk>;
+		};
+
+		twd-timer@20600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0x20600 0x20>;
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
+						  IRQ_TYPE_EDGE_RISING)>;
+			clocks = <&periph_clk>;
+		};
+
+		twd-watchdog@20620 {
+			compatible = "arm,cortex-a9-twd-wdt";
+			reg = <0x20620 0x20>;
+			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
+						  IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&periph_clk>;
+		};
+
+		gic: interrupt-controller@21000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x21000 0x1000>,
+			      <0x20100 0x100>;
+		};
+
+		L2: cache-controller@22000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x22000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+		};
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc: oscillator {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <25000000>;
+		};
+
+		iprocmed: iprocmed {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
+			clock-div = <2>;
+			clock-mult = <1>;
+		};
+
+		iprocslow: iprocslow {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		periph_clk: periph_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&a9pll>;
+			clock-div = <2>;
+			clock-mult = <1>;
+		};
+	};
+
+	axi: axi@18000000 {
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x18000000 0x0011c40c>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		gpioa: gpio@20 {
+			compatible = "brcm,nsp-gpio-a";
+			reg = <0x0020 0x70>,
+			      <0x3f1c4 0x1c>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			ngpios = <32>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-ranges = <&pinctrl 0 0 32>;
+		};
+
+		uart0: serial@300 {
+			compatible = "ns16550a";
+			reg = <0x0300 0x100>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc>;
+			status = "disabled";
+		};
+
+		uart1: serial@400 {
+			compatible = "ns16550a";
+			reg = <0x0400 0x100>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc>;
+			status = "disabled";
+		};
+
+		dma: dma@20000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x20000 0x1000>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&iprocslow>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+			dma-coherent;
+			status = "disabled";
+		};
+
+		sdio: mmc@21000 {
+			compatible = "brcm,sdhci-iproc-cygnus";
+			reg = <0x21000 0x100>;
+			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+			sdhci,auto-cmd12;
+			clocks = <&lcpll0 BCM_NSP_LCPLL0_SDIO_CLK>;
+			dma-coherent;
+			status = "disabled";
+		};
+
+		amac0: ethernet@22000 {
+			compatible = "brcm,nsp-amac";
+			reg = <0x022000 0x1000>,
+			      <0x110000 0x1000>;
+			reg-names = "amac_base", "idm_base";
+			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+			dma-coherent;
+			status = "disabled";
+		};
+
+		amac1: ethernet@23000 {
+			compatible = "brcm,nsp-amac";
+			reg = <0x023000 0x1000>,
+			      <0x111000 0x1000>;
+			reg-names = "amac_base", "idm_base";
+			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			dma-coherent;
+			status = "disabled";
+		};
+
+		amac2: ethernet@24000 {
+			compatible = "brcm,nsp-amac";
+			reg = <0x024000 0x1000>,
+			      <0x112000 0x1000>;
+			reg-names = "amac_base", "idm_base";
+			interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+			dma-coherent;
+			status = "disabled";
+		};
+
+		mailbox: mailbox@25c00 {
+			compatible = "brcm,iproc-fa2-mbox";
+			reg = <0x25c00 0x400>;
+			interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <1>;
+			brcm,rx-status-len = <32>;
+			brcm,use-bcm-hdr;
+			dma-coherent;
+		};
+
+		nand_controller: nand-controller@26000 {
+			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
+			reg = <0x026000 0x600>,
+			      <0x11b408 0x600>,
+			      <0x026f00 0x20>;
+			reg-names = "nand", "iproc-idm", "iproc-ext";
+			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			brcm,nand-has-wp;
+		};
+
+		qspi: spi@27200 {
+			compatible = "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi";
+			reg = <0x027200 0x184>,
+			      <0x027000 0x124>,
+			      <0x11c408 0x004>,
+			      <0x0273a0 0x01c>;
+			reg-names = "mspi", "bspi", "intr_regs",
+				    "intr_status_reg";
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "spi_lr_fullness_reached",
+					  "spi_lr_session_aborted",
+					  "spi_lr_impatient",
+					  "spi_lr_session_done",
+					  "spi_lr_overhead",
+					  "mspi_done",
+					  "mspi_halted";
+			clocks = <&iprocmed>;
+			clock-names = "iprocmed";
+			num-cs = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		xhci: usb@29000 {
+			compatible = "generic-xhci";
+			reg = <0x29000 0x1000>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&usb3_phy>;
+			phy-names = "usb3-phy";
+			dma-coherent;
+			status = "disabled";
+		};
+
+		ehci0: usb@2a000 {
+			compatible = "generic-ehci";
+			reg = <0x2a000 0x100>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			dma-coherent;
+			status = "disabled";
+		};
+
+		ohci0: usb@2b000 {
+			compatible = "generic-ohci";
+			reg = <0x2b000 0x100>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			dma-coherent;
+			status = "disabled";
+		};
+
+		crypto@2f000 {
+			compatible = "brcm,spum-nsp-crypto";
+			reg = <0x2f000 0x900>;
+			mboxes = <&mailbox 0>;
+		};
+
+		gpiob: gpio@30000 {
+			compatible = "brcm,iproc-nsp-gpio", "brcm,iproc-gpio";
+			reg = <0x30000 0x50>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			ngpios = <4>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pwm: pwm@31000 {
+			compatible = "brcm,iproc-pwm";
+			reg = <0x31000 0x28>;
+			clocks = <&osc>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		mdio: mdio@32000 {
+			compatible = "brcm,iproc-mdio";
+			reg = <0x32000 0x8>;
+			#size-cells = <0>;
+			#address-cells = <1>;
+		};
+
+		mdio-mux@32000 {
+			compatible = "mdio-mux-mmioreg", "mdio-mux";
+			reg = <0x32000 0x4>;
+			mux-mask = <0x200>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			mdio-parent-bus = <&mdio>;
+
+			mdio_int: mdio@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				usb3_phy: usb3-phy@10 {
+					compatible = "brcm,ns-bx-usb3-phy";
+					reg = <0x10>;
+					usb3-dmp-syscon = <&usb3_dmp>;
+					#phy-cells = <0>;
+					status = "disabled";
+				};
+			};
+
+			mdio_ext: mdio@200 {
+				reg = <0x200>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		rng: rng@33000 {
+			compatible = "brcm,bcm-nsp-rng";
+			reg = <0x33000 0x14>;
+		};
+
+		ccbtimer0: timer@34000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x34000 0x1000>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&iprocslow>;
+			clock-names = "apb_pclk";
+		};
+
+		ccbtimer1: timer@35000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x35000 0x1000>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&iprocslow>;
+			clock-names = "apb_pclk";
+		};
+
+		srab: ethernet-switch@36000 {
+			compatible = "brcm,nsp-srab";
+			reg = <0x36000 0x1000>,
+			      <0x3f308 0x8>,
+			      <0x3f410 0xc>;
+			reg-names = "srab", "mux_config", "sgmii_config";
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "link_state_p0",
+					  "link_state_p1",
+					  "link_state_p2",
+					  "link_state_p3",
+					  "link_state_p4",
+					  "link_state_p5",
+					  "link_state_p7",
+					  "link_state_p8",
+					  "phy",
+					  "ts",
+					  "imp_sleep_timer_p5",
+					  "imp_sleep_timer_p7",
+					  "imp_sleep_timer_p8";
+			status = "disabled";
+
+			/* ports are defined in board DTS */
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		i2c0: i2c@38000 {
+			compatible = "brcm,iproc-i2c";
+			reg = <0x38000 0x50>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <100000>;
+			dma-coherent;
+			status = "disabled";
+		};
+
+		watchdog@39000 {
+			compatible = "arm,sp805", "arm,primecell";
+			reg = <0x39000 0x1000>;
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&iprocslow>, <&iprocslow>;
+			clock-names = "wdog_clk", "apb_pclk";
+		};
+
+		lcpll0: lcpll0@3f100 {
+			#clock-cells = <1>;
+			compatible = "brcm,nsp-lcpll0";
+			reg = <0x3f100 0x14>;
+			clocks = <&osc>;
+			clock-output-names = "lcpll0", "pcie_phy", "sdio",
+					     "ddr_phy";
+		};
+
+		genpll: genpll@3f140 {
+			#clock-cells = <1>;
+			compatible = "brcm,nsp-genpll";
+			reg = <0x3f140 0x24>;
+			clocks = <&osc>;
+			clock-output-names = "genpll", "phy", "ethernetclk",
+					     "usbclk", "iprocfast", "sata1",
+					     "sata2";
+		};
+
+		pinctrl: pinctrl@3f1c0 {
+			compatible = "brcm,nsp-pinmux";
+			reg = <0x3f1c0 0x04>,
+			      <0x30028 0x04>,
+			      <0x3f408 0x04>;
+		};
+
+		thermal: thermal@3f2c0 {
+			compatible = "brcm,ns-thermal";
+			reg = <0x3f2c0 0x10>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		sata_phy: sata_phy@40100 {
+			compatible = "brcm,iproc-nsp-sata-phy";
+			reg = <0x40100 0x340>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			sata_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+
+			sata_phy1: sata-phy@1 {
+				reg = <1>;
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		sata: sata@41000 {
+			compatible = "brcm,bcm-nsp-ahci";
+			reg-names = "ahci", "top-ctrl";
+			reg = <0x41000 0x1000>, <0x40020 0x1c>;
+			interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dma-coherent;
+			status = "disabled";
+
+			sata0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata_phy0>;
+				phy-names = "sata-phy";
+			};
+
+			sata1: sata-port@1 {
+				reg = <1>;
+				phys = <&sata_phy1>;
+				phy-names = "sata-phy";
+			};
+		};
+
+		usb3_dmp: syscon@104000 {
+			reg = <0x104000 0x1000>;
+		};
+	};
+
+	pcie0: pcie@18012000 {
+		compatible = "brcm,iproc-pcie";
+		reg = <0x18012000 0x1000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+
+		linux,pci-domain = <0>;
+
+		bus-range = <0x00 0xff>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+
+		/* Note: The HW does not support I/O resources.  So,
+		 * only the memory resource range is being specified.
+		 */
+		ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
+
+		dma-coherent;
+		status = "disabled";
+
+		msi-parent = <&msi0>;
+		msi0: msi {
+			compatible = "brcm,iproc-msi";
+			msi-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+			brcm,pcie-msi-inten;
+		};
+	};
+
+	pcie1: pcie@18013000 {
+		compatible = "brcm,iproc-pcie";
+		reg = <0x18013000 0x1000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+
+		linux,pci-domain = <1>;
+
+		bus-range = <0x00 0xff>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+
+		/* Note: The HW does not support I/O resources.  So,
+		 * only the memory resource range is being specified.
+		 */
+		ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
+
+		dma-coherent;
+		status = "disabled";
+
+		msi-parent = <&msi1>;
+		msi1: msi {
+			compatible = "brcm,iproc-msi";
+			msi-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+			brcm,pcie-msi-inten;
+		};
+	};
+
+	pcie2: pcie@18014000 {
+		compatible = "brcm,iproc-pcie";
+		reg = <0x18014000 0x1000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+
+		linux,pci-domain = <2>;
+
+		bus-range = <0x00 0xff>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+
+		/* Note: The HW does not support I/O resources.  So,
+		 * only the memory resource range is being specified.
+		 */
+		ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>;
+
+		dma-coherent;
+		status = "disabled";
+
+		msi-parent = <&msi2>;
+		msi2: msi {
+			compatible = "brcm,iproc-msi";
+			msi-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+			brcm,pcie-msi-inten;
+		};
+	};
+
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+			coefficients = <(-556) 418000>;
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature     = <125000>;
+					hysteresis      = <0>;
+					type            = "critical";
+				};
+			};
+
+			cooling-maps {
+			};
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm11351.dtsi b/src/arm/broadcom/bcm11351.dtsi
new file mode 100644
index 0000000..53857e5
--- /dev/null
+++ b/src/arm/broadcom/bcm11351.dtsi
@@ -0,0 +1,412 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012-2013 Broadcom Corporation
+
+#include <dt-bindings/clock/bcm281xx.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "BCM11351 SoC";
+	compatible = "brcm,bcm11351";
+	interrupt-parent = <&gic>;
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			enable-method = "brcm,bcm11351-cpu-method";
+			secondary-boot-reg = <0x3500417c>;
+			reg = <1>;
+		};
+	};
+
+	gic: interrupt-controller@3ff00100 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+		interrupt-controller;
+		reg = <0x3ff01000 0x1000>,
+		      <0x3ff00100 0x100>;
+	};
+
+	smc@3404c000 {
+		compatible = "brcm,bcm11351-smc", "brcm,kona-smc";
+		reg = <0x3404c000 0x400>; /* 1 KiB in SRAM */
+	};
+
+	uartb: serial@3e000000 {
+		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
+		reg = <0x3e000000 0x1000>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB>;
+		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	uartb2: serial@3e001000 {
+		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
+		reg = <0x3e001000 0x1000>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB2>;
+		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	uartb3: serial@3e002000 {
+		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
+		reg = <0x3e002000 0x1000>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB3>;
+		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	uartb4: serial@3e003000 {
+		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
+		reg = <0x3e003000 0x1000>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB4>;
+		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	L2: l2-cache@3ff20000 {
+		compatible = "brcm,bcm11351-a2-pl310-cache";
+		reg = <0x3ff20000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+
+	watchdog@35002f40 {
+		compatible = "brcm,bcm11351-wdt", "brcm,kona-wdt";
+		reg = <0x35002f40 0x6c>;
+	};
+
+	timer@35006000 {
+		compatible = "brcm,kona-timer";
+		reg = <0x35006000 0x1000>;
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&aon_ccu BCM281XX_AON_CCU_HUB_TIMER>;
+	};
+
+	gpio: gpio@35003000 {
+		compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
+		reg = <0x35003000 0x800>;
+		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+	};
+
+	sdio1: mmc@3f180000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f180000 0x10000>;
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO1>;
+		status = "disabled";
+	};
+
+	sdio2: mmc@3f190000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f190000 0x10000>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO2>;
+		status = "disabled";
+	};
+
+	sdio3: mmc@3f1a0000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f1a0000 0x10000>;
+		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO3>;
+		status = "disabled";
+	};
+
+	sdio4: mmc@3f1b0000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f1b0000 0x10000>;
+		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO4>;
+		status = "disabled";
+	};
+
+	pinctrl@35004800 {
+		compatible = "brcm,bcm11351-pinctrl";
+		reg = <0x35004800 0x430>;
+	};
+
+	bsc1: i2c@3e016000 {
+		compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
+		reg = <0x3e016000 0x80>;
+		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_BSC1>;
+		status = "disabled";
+	};
+
+	bsc2: i2c@3e017000 {
+		compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
+		reg = <0x3e017000 0x80>;
+		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_BSC2>;
+		status = "disabled";
+	};
+
+	bsc3: i2c@3e018000 {
+		compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
+		reg = <0x3e018000 0x80>;
+		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_BSC3>;
+		status = "disabled";
+	};
+
+	pmu_bsc: i2c@3500d000 {
+		compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
+		reg = <0x3500d000 0x80>;
+		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&aon_ccu BCM281XX_AON_CCU_PMU_BSC>;
+		status = "disabled";
+	};
+
+	pwm: pwm@3e01a000 {
+		compatible = "brcm,bcm11351-pwm", "brcm,kona-pwm";
+		reg = <0x3e01a000 0xcc>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_PWM>;
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		root_ccu: root_ccu@35001000 {
+			compatible = "brcm,bcm11351-root-ccu";
+			reg = <0x35001000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "frac_1m";
+		};
+
+		hub_ccu: hub_ccu@34000000 {
+			compatible = "brcm,bcm11351-hub-ccu";
+			reg = <0x34000000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "tmon_1m";
+		};
+
+		aon_ccu: aon_ccu@35002000 {
+			compatible = "brcm,bcm11351-aon-ccu";
+			reg = <0x35002000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "hub_timer",
+					     "pmu_bsc",
+					     "pmu_bsc_var";
+		};
+
+		master_ccu: master_ccu@3f001000 {
+			compatible = "brcm,bcm11351-master-ccu";
+			reg = <0x3f001000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "sdio1",
+					     "sdio2",
+					     "sdio3",
+					     "sdio4",
+					     "usb_ic",
+					     "hsic2_48m",
+					     "hsic2_12m";
+		};
+
+		slave_ccu: slave_ccu@3e011000 {
+			compatible = "brcm,bcm11351-slave-ccu";
+			reg = <0x3e011000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "uartb",
+					     "uartb2",
+					     "uartb3",
+					     "uartb4",
+					     "ssp0",
+					     "ssp2",
+					     "bsc1",
+					     "bsc2",
+					     "bsc3",
+					     "pwm";
+		};
+
+		ref_1m_clk: ref_1m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <1000000>;
+		};
+
+		ref_32k_clk: ref_32k {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		bbl_32k_clk: bbl_32k {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		ref_13m_clk: ref_13m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+		};
+
+		var_13m_clk: var_13m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+		};
+
+		dft_19_5m_clk: dft_19_5m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <19500000>;
+		};
+
+		ref_crystal_clk: ref_crystal {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <26000000>;
+		};
+
+		ref_cx40_clk: ref_cx40 {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <40000000>;
+		};
+
+		ref_52m_clk: ref_52m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
+		};
+
+		var_52m_clk: var_52m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
+		};
+
+		usb_otg_ahb_clk: usb_otg_ahb {
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
+			#clock-cells = <0>;
+		};
+
+		ref_96m_clk: ref_96m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <96000000>;
+		};
+
+		var_96m_clk: var_96m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <96000000>;
+		};
+
+		ref_104m_clk: ref_104m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <104000000>;
+		};
+
+		var_104m_clk: var_104m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <104000000>;
+		};
+
+		ref_156m_clk: ref_156m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <156000000>;
+		};
+
+		var_156m_clk: var_156m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <156000000>;
+		};
+
+		ref_208m_clk: ref_208m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <208000000>;
+		};
+
+		var_208m_clk: var_208m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <208000000>;
+		};
+
+		ref_312m_clk: ref_312m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <312000000>;
+		};
+
+		var_312m_clk: var_312m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <312000000>;
+		};
+	};
+
+	usbotg: usb@3f120000 {
+		compatible = "snps,dwc2";
+		reg = <0x3f120000 0x10000>;
+		interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&usb_otg_ahb_clk>;
+		clock-names = "otg";
+		phys = <&usbphy>;
+		phy-names = "usb2-phy";
+		status = "disabled";
+	};
+
+	usbphy: usb-phy@3f130000 {
+		compatible = "brcm,kona-usb2-phy";
+		reg = <0x3f130000 0x28>;
+		#phy-cells = <0>;
+		status = "disabled";
+	};
+};
diff --git a/src/arm/broadcom/bcm21664-garnet.dts b/src/arm/broadcom/bcm21664-garnet.dts
new file mode 100644
index 0000000..8789fae
--- /dev/null
+++ b/src/arm/broadcom/bcm21664-garnet.dts
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Broadcom Corporation
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "bcm21664.dtsi"
+
+/ {
+	model = "BCM21664 Garnet board";
+	compatible = "brcm,bcm21664-garnet", "brcm,bcm21664";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>; /* 1 GB */
+	};
+};
+
+&sdio1 {
+	max-frequency = <48000000>;
+	status = "okay";
+};
+
+&sdio2 {
+	non-removable;
+	max-frequency = <48000000>;
+	status = "okay";
+};
+
+&sdio4 {
+	max-frequency = <48000000>;
+	cd-gpios = <&gpio 91 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&uartb {
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm21664.dtsi b/src/arm/broadcom/bcm21664.dtsi
new file mode 100644
index 0000000..fa73600
--- /dev/null
+++ b/src/arm/broadcom/bcm21664.dtsi
@@ -0,0 +1,345 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Broadcom Corporation
+
+#include <dt-bindings/clock/bcm21664.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "BCM21664 SoC";
+	compatible = "brcm,bcm21664";
+	interrupt-parent = <&gic>;
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			enable-method = "brcm,bcm11351-cpu-method";
+			secondary-boot-reg = <0x35004178>;
+			reg = <1>;
+		};
+	};
+
+	gic: interrupt-controller@3ff00100 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+		interrupt-controller;
+		reg = <0x3ff01000 0x1000>,
+		      <0x3ff00100 0x100>;
+	};
+
+	smc@3404e000 {
+		compatible = "brcm,bcm21664-smc", "brcm,kona-smc";
+		reg = <0x3404e000 0x400>; /* 1 KiB in SRAM */
+	};
+
+	uartb: serial@3e000000 {
+		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
+		reg = <0x3e000000 0x118>;
+		clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB>;
+		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	uartb2: serial@3e001000 {
+		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
+		reg = <0x3e001000 0x118>;
+		clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB2>;
+		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	uartb3: serial@3e002000 {
+		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
+		reg = <0x3e002000 0x118>;
+		clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB3>;
+		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	L2: cache-controller@3ff20000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x3ff20000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+
+	brcm,resetmgr@35001f00 {
+		compatible = "brcm,bcm21664-resetmgr";
+		reg = <0x35001f00 0x24>;
+	};
+
+	timer@35006000 {
+		compatible = "brcm,kona-timer";
+		reg = <0x35006000 0x1c>;
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&aon_ccu BCM21664_AON_CCU_HUB_TIMER>;
+	};
+
+	gpio: gpio@35003000 {
+		compatible = "brcm,bcm21664-gpio", "brcm,kona-gpio";
+		reg = <0x35003000 0x524>;
+		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+	};
+
+	sdio1: mmc@3f180000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f180000 0x801c>;
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO1>;
+		status = "disabled";
+	};
+
+	sdio2: mmc@3f190000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f190000 0x801c>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO2>;
+		status = "disabled";
+	};
+
+	sdio3: mmc@3f1a0000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f1a0000 0x801c>;
+		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO3>;
+		status = "disabled";
+	};
+
+	sdio4: mmc@3f1b0000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f1b0000 0x801c>;
+		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO4>;
+		status = "disabled";
+	};
+
+	bsc1: i2c@3e016000 {
+		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+		reg = <0x3e016000 0x70>;
+		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC1>;
+		status = "disabled";
+	};
+
+	bsc2: i2c@3e017000 {
+		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+		reg = <0x3e017000 0x70>;
+		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC2>;
+		status = "disabled";
+	};
+
+	bsc3: i2c@3e018000 {
+		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+		reg = <0x3e018000 0x70>;
+		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC3>;
+		status = "disabled";
+	};
+
+	bsc4: i2c@3e01c000 {
+		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+		reg = <0x3e01c000 0x70>;
+		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC4>;
+		status = "disabled";
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/*
+		 * Fixed clocks are defined before CCUs whose
+		 * clocks may depend on them.
+		 */
+
+		ref_32k_clk: ref_32k {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		bbl_32k_clk: bbl_32k {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		ref_13m_clk: ref_13m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+		};
+
+		var_13m_clk: var_13m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+		};
+
+		dft_19_5m_clk: dft_19_5m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <19500000>;
+		};
+
+		ref_crystal_clk: ref_crystal {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <26000000>;
+		};
+
+		ref_52m_clk: ref_52m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
+		};
+
+		var_52m_clk: var_52m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
+		};
+
+		usb_otg_ahb_clk: usb_otg_ahb {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
+		};
+
+		ref_96m_clk: ref_96m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <96000000>;
+		};
+
+		var_96m_clk: var_96m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <96000000>;
+		};
+
+		ref_104m_clk: ref_104m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <104000000>;
+		};
+
+		var_104m_clk: var_104m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <104000000>;
+		};
+
+		ref_156m_clk: ref_156m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <156000000>;
+		};
+
+		var_156m_clk: var_156m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <156000000>;
+		};
+
+		root_ccu: root_ccu@35001000 {
+			compatible = "brcm,bcm21664-root-ccu";
+			reg = <0x35001000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "frac_1m";
+		};
+
+		aon_ccu: aon_ccu@35002000 {
+			compatible = "brcm,bcm21664-aon-ccu";
+			reg = <0x35002000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "hub_timer";
+		};
+
+		master_ccu: master_ccu@3f001000 {
+			compatible = "brcm,bcm21664-master-ccu";
+			reg = <0x3f001000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "sdio1",
+					     "sdio2",
+					     "sdio3",
+					     "sdio4",
+					     "sdio1_sleep",
+					     "sdio2_sleep",
+					     "sdio3_sleep",
+					     "sdio4_sleep";
+		};
+
+		slave_ccu: slave_ccu@3e011000 {
+			compatible = "brcm,bcm21664-slave-ccu";
+			reg = <0x3e011000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "uartb",
+					     "uartb2",
+					     "uartb3",
+					     "bsc1",
+					     "bsc2",
+					     "bsc3",
+					     "bsc4";
+		};
+	};
+
+	usbotg: usb@3f120000 {
+		compatible = "snps,dwc2";
+		reg = <0x3f120000 0x10000>;
+		interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&usb_otg_ahb_clk>;
+		clock-names = "otg";
+		phys = <&usbphy>;
+		phy-names = "usb2-phy";
+		status = "disabled";
+	};
+
+	usbphy: usb-phy@3f130000 {
+		compatible = "brcm,kona-usb2-phy";
+		reg = <0x3f130000 0x28>;
+		#phy-cells = <0>;
+		status = "disabled";
+	};
+};
diff --git a/src/arm/broadcom/bcm23550-sparrow.dts b/src/arm/broadcom/bcm23550-sparrow.dts
new file mode 100644
index 0000000..ace7770
--- /dev/null
+++ b/src/arm/broadcom/bcm23550-sparrow.dts
@@ -0,0 +1,81 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "bcm23550.dtsi"
+
+/ {
+	model = "BCM23550 Sparrow board";
+	compatible = "brcm,bcm23550-sparrow", "brcm,bcm23550";
+
+	chosen {
+		stdout-path = "/slaves@3e000000/serial@0:115200n8";
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>; /* 512 MB */
+	};
+};
+
+&uartb {
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&sdio1 {
+	max-frequency = <48000000>;
+	status = "okay";
+};
+
+&sdio2 {
+	non-removable;
+	max-frequency = <48000000>;
+	status = "okay";
+};
+
+&sdio4 {
+	max-frequency = <48000000>;
+	cd-gpios = <&gpio 91 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm23550.dtsi b/src/arm/broadcom/bcm23550.dtsi
new file mode 100644
index 0000000..50ebe93
--- /dev/null
+++ b/src/arm/broadcom/bcm23550.dtsi
@@ -0,0 +1,413 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/* BCM23550 and BCM21664 have almost identical clocks */
+#include <dt-bindings/clock/bcm21664.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "BCM23550 SoC";
+	compatible = "brcm,bcm23550";
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0>;
+			clock-frequency = <1000000000>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			enable-method = "brcm,bcm23550";
+			secondary-boot-reg = <0x35004178>;
+			reg = <1>;
+			clock-frequency = <1000000000>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			enable-method = "brcm,bcm23550";
+			secondary-boot-reg = <0x35004178>;
+			reg = <2>;
+			clock-frequency = <1000000000>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			enable-method = "brcm,bcm23550";
+			secondary-boot-reg = <0x35004178>;
+			reg = <3>;
+			clock-frequency = <1000000000>;
+		};
+	};
+
+	/* Hub bus */
+	hub@34000000 {
+		compatible = "simple-bus";
+		ranges = <0 0x34000000 0x102f83ac>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		smc@4e000 {
+			compatible = "brcm,bcm23550-smc", "brcm,kona-smc";
+			reg = <0x0004e000 0x400>; /* 1 KiB in SRAM */
+		};
+
+		resetmgr: reset-controller@1001f00 {
+			compatible = "brcm,bcm21664-resetmgr";
+			reg = <0x01001f00 0x24>;
+		};
+
+		gpio: gpio@1003000 {
+			compatible = "brcm,bcm23550-gpio", "brcm,kona-gpio";
+			reg = <0x01003000 0x524>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+		};
+
+		timer@1006000 {
+			compatible = "brcm,kona-timer";
+			reg = <0x01006000 0x1c>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&aon_ccu BCM21664_AON_CCU_HUB_TIMER>;
+		};
+	};
+
+	/* Slaves bus */
+	slaves@3e000000 {
+		compatible = "simple-bus";
+		ranges = <0 0x3e000000 0x0001c070>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		uartb: serial@0 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x00000000 0x118>;
+			clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB>;
+			interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			status = "disabled";
+		};
+
+		uartb2: serial@1000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x00001000 0x118>;
+			clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB2>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			status = "disabled";
+		};
+
+		uartb3: serial@2000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x00002000 0x118>;
+			clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB3>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			status = "disabled";
+		};
+
+		bsc1: i2c@16000 {
+			compatible = "brcm,bcm23550-i2c", "brcm,kona-i2c";
+			reg = <0x00016000 0x70>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC1>;
+			status = "disabled";
+		};
+
+		bsc2: i2c@17000 {
+			compatible = "brcm,bcm23550-i2c", "brcm,kona-i2c";
+			reg = <0x00017000 0x70>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC2>;
+			status = "disabled";
+		};
+
+		bsc3: i2c@18000 {
+			compatible = "brcm,bcm23550-i2c", "brcm,kona-i2c";
+			reg = <0x00018000 0x70>;
+			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC3>;
+			status = "disabled";
+		};
+
+		bsc4: i2c@1c000 {
+			compatible = "brcm,bcm23550-i2c", "brcm,kona-i2c";
+			reg = <0x0001c000 0x70>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC4>;
+			status = "disabled";
+		};
+	};
+
+	/* Apps bus */
+	apps@3e300000 {
+		compatible = "simple-bus";
+		ranges = <0 0x3e300000 0x01b77000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		usbotg: usb@e20000 {
+			compatible = "snps,dwc2";
+			reg = <0x00e20000 0x10000>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&usb_otg_ahb_clk>;
+			clock-names = "otg";
+			phys = <&usbphy>;
+			phy-names = "usb2-phy";
+			status = "disabled";
+		};
+
+		usbphy: usb-phy@e30000 {
+			compatible = "brcm,kona-usb2-phy";
+			reg = <0x00e30000 0x28>;
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		sdio1: mmc@e80000 {
+			compatible = "brcm,kona-sdhci";
+			reg = <0x00e80000 0x801c>;
+			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO1>;
+			status = "disabled";
+		};
+
+		sdio2: mmc@e90000 {
+			compatible = "brcm,kona-sdhci";
+			reg = <0x00e90000 0x801c>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO2>;
+			status = "disabled";
+		};
+
+		sdio3: mmc@ea0000 {
+			compatible = "brcm,kona-sdhci";
+			reg = <0x00ea0000 0x801c>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO3>;
+			status = "disabled";
+		};
+
+		sdio4: mmc@eb0000 {
+			compatible = "brcm,kona-sdhci";
+			reg = <0x00eb0000 0x801c>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO4>;
+			status = "disabled";
+		};
+
+		cdc: cdc@1b0e000 {
+			compatible = "brcm,bcm23550-cdc";
+			reg = <0x01b0e000 0x78>;
+		};
+
+		gic: interrupt-controller@1b21000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x01b21000 0x1000>,
+			      <0x01b22000 0x1000>;
+		};
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/*
+		 * Fixed clocks are defined before CCUs whose
+		 * clocks may depend on them.
+		 */
+
+		ref_32k_clk: ref_32k {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		bbl_32k_clk: bbl_32k {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		ref_13m_clk: ref_13m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+		};
+
+		var_13m_clk: var_13m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+		};
+
+		dft_19_5m_clk: dft_19_5m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <19500000>;
+		};
+
+		ref_crystal_clk: ref_crystal {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <26000000>;
+		};
+
+		ref_52m_clk: ref_52m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
+		};
+
+		var_52m_clk: var_52m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
+		};
+
+		usb_otg_ahb_clk: usb_otg_ahb {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
+		};
+
+		ref_96m_clk: ref_96m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <96000000>;
+		};
+
+		var_96m_clk: var_96m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <96000000>;
+		};
+
+		ref_104m_clk: ref_104m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <104000000>;
+		};
+
+		var_104m_clk: var_104m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <104000000>;
+		};
+
+		ref_156m_clk: ref_156m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <156000000>;
+		};
+
+		var_156m_clk: var_156m {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <156000000>;
+		};
+
+		root_ccu: root_ccu@35001000 {
+			compatible = "brcm,bcm21664-root-ccu";
+			reg = <0x35001000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "frac_1m";
+		};
+
+		aon_ccu: aon_ccu@35002000 {
+			compatible = "brcm,bcm21664-aon-ccu";
+			reg = <0x35002000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "hub_timer";
+		};
+
+		slave_ccu: slave_ccu@3e011000 {
+			compatible = "brcm,bcm21664-slave-ccu";
+			reg = <0x3e011000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "uartb",
+					     "uartb2",
+					     "uartb3",
+					     "bsc1",
+					     "bsc2",
+					     "bsc3",
+					     "bsc4";
+		};
+
+		master_ccu: master_ccu@3f001000 {
+			compatible = "brcm,bcm21664-master-ccu";
+			reg = <0x3f001000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "sdio1",
+					     "sdio2",
+					     "sdio3",
+					     "sdio4",
+					     "sdio1_sleep",
+					     "sdio2_sleep",
+					     "sdio3_sleep",
+					     "sdio4_sleep";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm2711-rpi-4-b.dts b/src/arm/broadcom/bcm2711-rpi-4-b.dts
new file mode 100644
index 0000000..d5f8823
--- /dev/null
+++ b/src/arm/broadcom/bcm2711-rpi-4-b.dts
@@ -0,0 +1,243 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711.dtsi"
+#include "bcm2711-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-usb-peripheral.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
+	model = "Raspberry Pi 4 Model B";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	sd_io_1v8_reg: regulator-sd-io-1v8 {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-sd-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-settling-time-us = <5000>;
+		gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1>,
+			 <3300000 0x0>;
+		status = "okay";
+	};
+
+	sd_vcc_reg: regulator-sd-vcc {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&bt {
+	shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+};
+
+&ddc0 {
+	status = "okay";
+};
+
+&ddc1 {
+	status = "okay";
+};
+
+&expgpio {
+	gpio-line-names = "BT_ON",		/*  0 */
+			  "WL_ON",
+			  "PWR_LED_OFF",
+			  "GLOBAL_RESET",
+			  "VDD_SD_IO_SEL",
+			  "CAM_GPIO",		/*  5 */
+			  "SD_PWR_ON",
+			  "";
+};
+
+&gpio {
+	/*
+	 * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",		/*  0 */
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",		/*  5 */
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",		/* 10 */
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",		/* 15 */
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",		/* 20 */
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",		/* 25 */
+			  "GPIO26",
+			  "GPIO27",
+			  "RGMII_MDIO",
+			  "RGMIO_MDC",
+			  /* Used by BT module */
+			  "CTS0",		/* 30 */
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",		/* 35 */
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  /* Shared with SPI flash */
+			  "PWM0_MISO",		/* 40 */
+			  "PWM1_MOSI",
+			  "STATUS_LED_G_CLK",
+			  "SPIFLASH_CE_N",
+			  "SDA0",
+			  "SCL0",		/* 45 */
+			  "RGMII_RXCLK",
+			  "RGMII_RXCTL",
+			  "RGMII_RXD0",
+			  "RGMII_RXD1",
+			  "RGMII_RXD2",		/* 50 */
+			  "RGMII_RXD3",
+			  "RGMII_TXCLK",
+			  "RGMII_TXCTL",
+			  "RGMII_TXD0",
+			  "RGMII_TXD1",		/* 55 */
+			  "RGMII_TXD2",
+			  "RGMII_TXD3";
+};
+
+&hdmi0 {
+	status = "okay";
+};
+
+&hdmi1 {
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led_pwr: led-pwr {
+		label = "PWR";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
+&pixelvalve0 {
+	status = "okay";
+};
+
+&pixelvalve1 {
+	status = "okay";
+};
+
+&pixelvalve2 {
+	status = "okay";
+};
+
+&pixelvalve4 {
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>;
+	status = "okay";
+};
+
+/* EMMC2 is used to drive the SD card */
+&emmc2 {
+	vqmmc-supply = <&sd_io_1v8_reg>;
+	vmmc-supply = <&sd_vcc_reg>;
+	broken-cd;
+	status = "okay";
+};
+
+&genet {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-rxid";
+	status = "okay";
+};
+
+&genet_mdio {
+	phy1: ethernet-phy@1 {
+		/* No PHY interrupt */
+		reg = <0x1>;
+	};
+};
+
+&pcie0 {
+	pci@0,0 {
+		device_type = "pci";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		reg = <0 0 0 0 0>;
+
+		usb@0,0 {
+			reg = <0 0 0 0 0>;
+			resets = <&reset RASPBERRYPI_FIRMWARE_RESET_ID_USB>;
+		};
+	};
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
+	uart-has-rtscts;
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&vc4 {
+	status = "okay";
+};
+
+&vec {
+	status = "disabled";
+};
+
+&wifi_pwrseq {
+	reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
diff --git a/src/arm/broadcom/bcm2711-rpi-400.dts b/src/arm/broadcom/bcm2711-rpi-400.dts
new file mode 100644
index 0000000..5a2869a
--- /dev/null
+++ b/src/arm/broadcom/bcm2711-rpi-400.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711-rpi-4-b.dts"
+
+/ {
+	compatible = "raspberrypi,400", "brcm,bcm2711";
+	model = "Raspberry Pi 400";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&expgpio 5 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&expgpio {
+	gpio-line-names = "BT_ON",
+			  "WL_ON",
+			  "PWR_LED_OFF",
+			  "GLOBAL_RESET",
+			  "VDD_SD_IO_SEL",
+			  "GLOBAL_SHUTDOWN",
+			  "SD_PWR_ON",
+			  "SHUTDOWN_REQUEST";
+};
+
+&genet_mdio {
+	clock-frequency = <1950000>;
+};
+
+&led_pwr {
+	gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+/delete-node/ &led_act;
+
+&pm {
+	/delete-property/ system-power-controller;
+};
diff --git a/src/arm/broadcom/bcm2711-rpi-cm4-io.dts b/src/arm/broadcom/bcm2711-rpi-cm4-io.dts
new file mode 100644
index 0000000..d7ba02f
--- /dev/null
+++ b/src/arm/broadcom/bcm2711-rpi-cm4-io.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711-rpi-cm4.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	model = "Raspberry Pi Compute Module 4 IO Board";
+};
+
+&ddc0 {
+	status = "okay";
+};
+
+&ddc1 {
+	status = "okay";
+};
+
+&gpio {
+	/*
+	 * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "RGMII_MDIO",
+			  "RGMIO_MDC",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  /* Shared with SPI flash */
+			  "PWM0_MISO",
+			  "PWM1_MOSI",
+			  "STATUS_LED_G_CLK",
+			  "SPIFLASH_CE_N",
+			  "SDA0",
+			  "SCL0",
+			  "RGMII_RXCLK",
+			  "RGMII_RXCTL",
+			  "RGMII_RXD0",
+			  "RGMII_RXD1",
+			  "RGMII_RXD2",
+			  "RGMII_RXD3",
+			  "RGMII_TXCLK",
+			  "RGMII_TXCTL",
+			  "RGMII_TXD0",
+			  "RGMII_TXD1",
+			  "RGMII_TXD2",
+			  "RGMII_TXD3";
+};
+
+&hdmi0 {
+	status = "okay";
+};
+
+&hdmi1 {
+	status = "okay";
+};
+
+&genet {
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
+&pixelvalve0 {
+	status = "okay";
+};
+
+&pixelvalve1 {
+	status = "okay";
+};
+
+&pixelvalve2 {
+	status = "okay";
+};
+
+&pixelvalve4 {
+	status = "okay";
+};
+
+&vc4 {
+	status = "okay";
+};
+
+&vec {
+	status = "disabled";
+};
diff --git a/src/arm/broadcom/bcm2711-rpi-cm4.dtsi b/src/arm/broadcom/bcm2711-rpi-cm4.dtsi
new file mode 100644
index 0000000..48e63ab
--- /dev/null
+++ b/src/arm/broadcom/bcm2711-rpi-cm4.dtsi
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711.dtsi"
+#include "bcm2711-rpi.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,4-compute-module", "brcm,bcm2711";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	sd_io_1v8_reg: regulator-sd-io-1v8 {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-sd-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-settling-time-us = <5000>;
+		gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1>,
+			 <3300000 0x0>;
+		status = "okay";
+	};
+
+	sd_vcc_reg: regulator-sd-vcc {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&bt {
+	shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+};
+
+/* EMMC2 is used to drive the eMMC */
+&emmc2 {
+	bus-width = <8>;
+	vqmmc-supply = <&sd_io_1v8_reg>;
+	vmmc-supply = <&sd_vcc_reg>;
+	broken-cd;
+	/* Even the IP block is limited to 100 MHz
+	 * this provides a throughput gain
+	 */
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&expgpio {
+	gpio-line-names = "BT_ON",
+			  "WL_ON",
+			  "PWR_LED_OFF",
+			  "ANT1",
+			  "VDD_SD_IO_SEL",
+			  "CAM_GPIO",
+			  "SD_PWR_ON",
+			  "ANT2";
+
+	ant1: ant1-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>;
+		/* internal antenna enabled */
+		output-high;
+		line-name = "ant1";
+	};
+
+	ant2: ant2-hog {
+		gpio-hog;
+		gpios = <7 GPIO_ACTIVE_HIGH>;
+		/* external antenna disabled */
+		output-low;
+		line-name = "ant2";
+	};
+};
+
+&genet {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-rxid";
+	status = "okay";
+};
+
+&genet_mdio {
+	phy1: ethernet-phy@0 {
+		/* No PHY interrupt */
+		reg = <0x0>;
+	};
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
+	uart-has-rtscts;
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&wifi_pwrseq {
+	reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
diff --git a/src/arm/broadcom/bcm2711-rpi.dtsi b/src/arm/broadcom/bcm2711-rpi.dtsi
new file mode 100644
index 0000000..98817a6
--- /dev/null
+++ b/src/arm/broadcom/bcm2711-rpi.dtsi
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm2835-rpi.dtsi"
+
+#include <dt-bindings/reset/raspberrypi,firmware-reset.h>
+
+/ {
+	/* Will be filled by the bootloader */
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0 0>;
+	};
+
+	aliases {
+		emmc2bus = &emmc2bus;
+		ethernet0 = &genet;
+		pcie0 = &pcie0;
+		blconfig = &blconfig;
+	};
+};
+
+&firmware {
+	firmware_clocks: clocks {
+		compatible = "raspberrypi,firmware-clocks";
+		#clock-cells = <1>;
+	};
+
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		status = "okay";
+	};
+
+	reset: reset {
+		compatible = "raspberrypi,firmware-reset";
+		#reset-cells = <1>;
+	};
+};
+
+&hdmi0 {
+	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>;
+	clock-names = "hdmi", "bvb", "audio", "cec";
+	wifi-2.4ghz-coexistence;
+};
+
+&hdmi1 {
+	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>;
+	clock-names = "hdmi", "bvb", "audio", "cec";
+	wifi-2.4ghz-coexistence;
+};
+
+&hvs {
+	clocks = <&firmware_clocks 4>;
+};
+
+&rmem {
+	/*
+	 * RPi4's co-processor will copy the board's bootloader configuration
+	 * into memory for the OS to consume. It'll also update this node with
+	 * its placement information.
+	 */
+	blconfig: nvram@0 {
+		compatible = "raspberrypi,bootloader-config", "nvmem-rmem";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0 0x0 0x0>;
+		no-map;
+		status = "disabled";
+	};
+};
+
+&v3d {
+	clocks = <&firmware_clocks 5>;
+};
+
+&vchiq {
+	interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/src/arm/broadcom/bcm2711.dtsi b/src/arm/broadcom/bcm2711.dtsi
new file mode 100644
index 0000000..4a379a1
--- /dev/null
+++ b/src/arm/broadcom/bcm2711.dtsi
@@ -0,0 +1,1172 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm283x.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/bcm2835-pm.h>
+
+/ {
+	compatible = "brcm,bcm2711";
+
+	#address-cells = <2>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gicv2>;
+
+	vc4: gpu {
+		compatible = "brcm,bcm2711-vc5";
+		status = "disabled";
+	};
+
+	clk_27MHz: clk-27M {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <27000000>;
+		clock-output-names = "27MHz-clock";
+	};
+
+	clk_108MHz: clk-108M {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <108000000>;
+		clock-output-names = "108MHz-clock";
+	};
+
+	soc {
+		/*
+		 * Defined ranges:
+		 *   Common BCM283x peripherals
+		 *   BCM2711-specific peripherals
+		 *   ARM-local peripherals
+		 */
+		ranges = <0x7e000000  0x0 0xfe000000  0x01800000>,
+			 <0x7c000000  0x0 0xfc000000  0x02000000>,
+			 <0x40000000  0x0 0xff800000  0x00800000>;
+		/* Emulate a contiguous 30-bit address range for DMA */
+		dma-ranges = <0xc0000000  0x0 0x00000000  0x40000000>;
+
+		/*
+		 * This node is the provider for the enable-method for
+		 * bringing up secondary cores.
+		 */
+		local_intc: interrupt-controller@40000000 {
+			compatible = "brcm,bcm2836-l1-intc";
+			reg = <0x40000000 0x100>;
+		};
+
+		gicv2: interrupt-controller@40041000 {
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			compatible = "arm,gic-400";
+			reg =	<0x40041000 0x1000>,
+				<0x40042000 0x2000>,
+				<0x40044000 0x2000>,
+				<0x40046000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
+						 IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		avs_monitor: avs-monitor@7d5d2000 {
+			compatible = "brcm,bcm2711-avs-monitor",
+				     "syscon", "simple-mfd";
+			reg = <0x7d5d2000 0xf00>;
+
+			thermal: thermal {
+				compatible = "brcm,bcm2711-thermal";
+				#thermal-sensor-cells = <0>;
+			};
+		};
+
+		dma: dma-controller@7e007000 {
+			compatible = "brcm,bcm2835-dma";
+			reg = <0x7e007000 0xb00>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+				     /* DMA lite 7 - 10 */
+				     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dma0",
+					  "dma1",
+					  "dma2",
+					  "dma3",
+					  "dma4",
+					  "dma5",
+					  "dma6",
+					  "dma7",
+					  "dma8",
+					  "dma9",
+					  "dma10";
+			#dma-cells = <1>;
+			brcm,dma-channel-mask = <0x07f5>;
+		};
+
+		pm: watchdog@7e100000 {
+			compatible = "brcm,bcm2711-pm", "brcm,bcm2835-pm-wdt";
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0x7e100000 0x114>,
+			      <0x7e00a000 0x24>,
+			      <0x7ec11000 0x20>;
+			reg-names = "pm", "asb", "rpivid_asb";
+			clocks = <&clocks BCM2835_CLOCK_V3D>,
+				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
+				 <&clocks BCM2835_CLOCK_H264>,
+				 <&clocks BCM2835_CLOCK_ISP>;
+			clock-names = "v3d", "peri_image", "h264", "isp";
+			system-power-controller;
+		};
+
+		rng@7e104000 {
+			compatible = "brcm,bcm2711-rng200";
+			reg = <0x7e104000 0x28>;
+		};
+
+		uart2: serial@7e201400 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201400 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+			status = "disabled";
+		};
+
+		uart3: serial@7e201600 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201600 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+			status = "disabled";
+		};
+
+		uart4: serial@7e201800 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201800 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+			status = "disabled";
+		};
+
+		uart5: serial@7e201a00 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201a00 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+			status = "disabled";
+		};
+
+		spi3: spi@7e204600 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204600 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi4: spi@7e204800 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204800 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi5: spi@7e204a00 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204a00 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi6: spi@7e204c00 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204c00 0x0200>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@7e205600 {
+			compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
+			reg = <0x7e205600 0x200>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@7e205800 {
+			compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
+			reg = <0x7e205800 0x200>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c5: i2c@7e205a00 {
+			compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
+			reg = <0x7e205a00 0x200>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c6: i2c@7e205c00 {
+			compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
+			reg = <0x7e205c00 0x200>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pixelvalve0: pixelvalve@7e206000 {
+			compatible = "brcm,bcm2711-pixelvalve0";
+			reg = <0x7e206000 0x100>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		pixelvalve1: pixelvalve@7e207000 {
+			compatible = "brcm,bcm2711-pixelvalve1";
+			reg = <0x7e207000 0x100>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		pixelvalve2: pixelvalve@7e20a000 {
+			compatible = "brcm,bcm2711-pixelvalve2";
+			reg = <0x7e20a000 0x100>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		pwm1: pwm@7e20c800 {
+			compatible = "brcm,bcm2835-pwm";
+			reg = <0x7e20c800 0x28>;
+			clocks = <&clocks BCM2835_CLOCK_PWM>;
+			assigned-clocks = <&clocks BCM2835_CLOCK_PWM>;
+			assigned-clock-rates = <10000000>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		pixelvalve4: pixelvalve@7e216000 {
+			compatible = "brcm,bcm2711-pixelvalve4";
+			reg = <0x7e216000 0x100>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		hvs: hvs@7e400000 {
+			compatible = "brcm,bcm2711-hvs";
+			reg = <0x7e400000 0x8000>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pixelvalve3: pixelvalve@7ec12000 {
+			compatible = "brcm,bcm2711-pixelvalve3";
+			reg = <0x7ec12000 0x100>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		vec: vec@7ec13000 {
+			compatible = "brcm,bcm2711-vec";
+			reg = <0x7ec13000 0x1000>;
+			clocks = <&clocks BCM2835_CLOCK_VEC>;
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		dvp: clock@7ef00000 {
+			compatible = "brcm,brcm2711-dvp";
+			reg = <0x7ef00000 0x10>;
+			clocks = <&clk_108MHz>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		aon_intr: interrupt-controller@7ef00100 {
+			compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc";
+			reg = <0x7ef00100 0x30>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		hdmi0: hdmi@7ef00700 {
+			compatible = "brcm,bcm2711-hdmi0";
+			reg = <0x7ef00700 0x300>,
+			      <0x7ef00300 0x200>,
+			      <0x7ef00f00 0x80>,
+			      <0x7ef00f80 0x80>,
+			      <0x7ef01b00 0x200>,
+			      <0x7ef01f00 0x400>,
+			      <0x7ef00200 0x80>,
+			      <0x7ef04300 0x100>,
+			      <0x7ef20000 0x100>;
+			reg-names = "hdmi",
+				    "dvp",
+				    "phy",
+				    "rm",
+				    "packet",
+				    "metadata",
+				    "csc",
+				    "cec",
+				    "hd";
+			clock-names = "hdmi", "bvb", "audio", "cec";
+			resets = <&dvp 0>;
+			interrupt-parent = <&aon_intr>;
+			interrupts = <0>, <1>, <2>,
+				     <3>, <4>, <5>;
+			interrupt-names = "cec-tx", "cec-rx", "cec-low",
+					  "wakeup", "hpd-connected", "hpd-removed";
+			ddc = <&ddc0>;
+			dmas = <&dma 10>;
+			dma-names = "audio-rx";
+			status = "disabled";
+		};
+
+		ddc0: i2c@7ef04500 {
+			compatible = "brcm,bcm2711-hdmi-i2c";
+			reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>;
+			reg-names = "bsc", "auto-i2c";
+			clock-frequency = <97500>;
+			status = "disabled";
+		};
+
+		hdmi1: hdmi@7ef05700 {
+			compatible = "brcm,bcm2711-hdmi1";
+			reg = <0x7ef05700 0x300>,
+			      <0x7ef05300 0x200>,
+			      <0x7ef05f00 0x80>,
+			      <0x7ef05f80 0x80>,
+			      <0x7ef06b00 0x200>,
+			      <0x7ef06f00 0x400>,
+			      <0x7ef00280 0x80>,
+			      <0x7ef09300 0x100>,
+			      <0x7ef20000 0x100>;
+			reg-names = "hdmi",
+				    "dvp",
+				    "phy",
+				    "rm",
+				    "packet",
+				    "metadata",
+				    "csc",
+				    "cec",
+				    "hd";
+			ddc = <&ddc1>;
+			clock-names = "hdmi", "bvb", "audio", "cec";
+			resets = <&dvp 1>;
+			interrupt-parent = <&aon_intr>;
+			interrupts = <8>, <7>, <6>,
+				     <9>, <10>, <11>;
+			interrupt-names = "cec-tx", "cec-rx", "cec-low",
+					  "wakeup", "hpd-connected", "hpd-removed";
+			dmas = <&dma 17>;
+			dma-names = "audio-rx";
+			status = "disabled";
+		};
+
+		ddc1: i2c@7ef09500 {
+			compatible = "brcm,bcm2711-hdmi-i2c";
+			reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>;
+			reg-names = "bsc", "auto-i2c";
+			clock-frequency = <97500>;
+			status = "disabled";
+		};
+	};
+
+	/*
+	 * emmc2 has different DMA constraints based on SoC revisions. It was
+	 * moved into its own bus, so as for RPi4's firmware to update them.
+	 * The firmware will find whether the emmc2bus alias is defined, and if
+	 * so, it'll edit the dma-ranges property below accordingly.
+	 */
+	emmc2bus: emmc2bus {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		ranges = <0x0 0x7e000000  0x0 0xfe000000  0x01800000>;
+		dma-ranges = <0x0 0xc0000000  0x0 0x00000000  0x40000000>;
+
+		emmc2: mmc@7e340000 {
+			compatible = "brcm,bcm2711-emmc2";
+			reg = <0x0 0x7e340000 0x100>;
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2711_CLOCK_EMMC2>;
+			status = "disabled";
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a72-pmu", "arm,armv8-pmuv3";
+		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) |
+					  IRQ_TYPE_LEVEL_LOW)>;
+		/* This only applies to the ARMv7 stub */
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	cpus: cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
+
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 * https://developer.arm.com/documentation/100095/0003
+		 * /Level-1-Memory-System/About-the-L1-memory-system?lang=en
+		 * Source for d/i-cache-size
+		 * https://www.raspberrypi.com/documentation/computers
+		 * /processors.html#bcm2711
+		 */
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000d8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <1>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000e0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <2>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000e8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <3>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000f0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
+		};
+
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 *  https://developer.arm.com/documentation/100095/0003
+		 *  /Level-2-Memory-System/About-the-L2-memory-system?lang=en
+		 *  Source for d/i-cache-size
+		 *  https://www.raspberrypi.com/documentation/computers
+		 *  /processors.html#bcm2711
+		 */
+		l2: l2-cache0 {
+			compatible = "cache";
+			cache-unified;
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>; // 1MiB(size)/64(line-size)=16384ways/16-way set
+			cache-level = <2>;
+		};
+	};
+
+	scb {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		ranges = <0x0 0x7c000000  0x0 0xfc000000  0x03800000>,
+			 <0x6 0x00000000  0x6 0x00000000  0x40000000>;
+
+		pcie0: pcie@7d500000 {
+			compatible = "brcm,bcm2711-pcie";
+			reg = <0x0 0x7d500000 0x9310>;
+			device_type = "pci";
+			#address-cells = <3>;
+			#interrupt-cells = <1>;
+			#size-cells = <2>;
+			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pcie", "msi";
+			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+			interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143
+							IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &gicv2 GIC_SPI 144
+							IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &gicv2 GIC_SPI 145
+							IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &gicv2 GIC_SPI 146
+							IRQ_TYPE_LEVEL_HIGH>;
+			msi-controller;
+			msi-parent = <&pcie0>;
+
+			ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000
+				  0x0 0x04000000>;
+			/*
+			 * The wrapper around the PCIe block has a bug
+			 * preventing it from accessing beyond the first 3GB of
+			 * memory.
+			 */
+			dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000
+				      0x0 0xc0000000>;
+			brcm,enable-ssc;
+		};
+
+		genet: ethernet@7d580000 {
+			compatible = "brcm,bcm2711-genet-v5";
+			reg = <0x0 0x7d580000 0x10000>;
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+
+			genet_mdio: mdio@e14 {
+				compatible = "brcm,genet-mdio-v5";
+				reg = <0xe14 0x8>;
+				reg-names = "mdio";
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
+			};
+		};
+
+		v3d: gpu@7ec00000 {
+			compatible = "brcm,2711-v3d";
+			reg = <0x0 0x7ec00000 0x4000>,
+			      <0x0 0x7ec04000 0x4000>;
+			reg-names = "hub", "core0";
+
+			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
+			resets = <&pm BCM2835_RESET_V3D>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+};
+
+&clk_osc {
+	clock-frequency = <54000000>;
+};
+
+&clocks {
+	compatible = "brcm,bcm2711-cprman";
+};
+
+&cpu_thermal {
+	coefficients = <(-487) 410040>;
+	thermal-sensors = <&thermal>;
+};
+
+&dsi0 {
+	interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&dsi1 {
+	interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+	compatible = "brcm,bcm2711-dsi1";
+};
+
+&gpio {
+	compatible = "brcm,bcm2711-gpio";
+	interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+
+	gpio-ranges = <&gpio 0 0 58>;
+
+	gpclk0_gpio49: gpclk0-gpio49 {
+		pin-gpclk {
+			pins = "gpio49";
+			function = "alt1";
+			bias-disable;
+		};
+	};
+	gpclk1_gpio50: gpclk1-gpio50 {
+		pin-gpclk {
+			pins = "gpio50";
+			function = "alt1";
+			bias-disable;
+		};
+	};
+	gpclk2_gpio51: gpclk2-gpio51 {
+		pin-gpclk {
+			pins = "gpio51";
+			function = "alt1";
+			bias-disable;
+		};
+	};
+
+	i2c0_gpio46: i2c0-gpio46 {
+		pin-sda {
+			function = "alt0";
+			pins = "gpio46";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt0";
+			pins = "gpio47";
+			bias-disable;
+		};
+	};
+	i2c1_gpio46: i2c1-gpio46 {
+		pin-sda {
+			function = "alt1";
+			pins = "gpio46";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt1";
+			pins = "gpio47";
+			bias-disable;
+		};
+	};
+	i2c3_gpio2: i2c3-gpio2 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio2";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio3";
+			bias-disable;
+		};
+	};
+	i2c3_gpio4: i2c3-gpio4 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio4";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio5";
+			bias-disable;
+		};
+	};
+	i2c4_gpio6: i2c4-gpio6 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio6";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio7";
+			bias-disable;
+		};
+	};
+	i2c4_gpio8: i2c4-gpio8 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio8";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio9";
+			bias-disable;
+		};
+	};
+	i2c5_gpio10: i2c5-gpio10 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio10";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio11";
+			bias-disable;
+		};
+	};
+	i2c5_gpio12: i2c5-gpio12 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio12";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio13";
+			bias-disable;
+		};
+	};
+	i2c6_gpio0: i2c6-gpio0 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio0";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio1";
+			bias-disable;
+		};
+	};
+	i2c6_gpio22: i2c6-gpio22 {
+		pin-sda {
+			function = "alt5";
+			pins = "gpio22";
+			bias-pull-up;
+		};
+		pin-scl {
+			function = "alt5";
+			pins = "gpio23";
+			bias-disable;
+		};
+	};
+	i2c_slave_gpio8: i2c-slave-gpio8 {
+		pins-i2c-slave {
+			pins = "gpio8",
+			       "gpio9",
+			       "gpio10",
+			       "gpio11";
+			function = "alt3";
+		};
+	};
+
+	jtag_gpio48: jtag-gpio48 {
+		pins-jtag {
+			pins = "gpio48",
+			       "gpio49",
+			       "gpio50",
+			       "gpio51",
+			       "gpio52",
+			       "gpio53";
+			function = "alt4";
+		};
+	};
+
+	mii_gpio28: mii-gpio28 {
+		pins-mii {
+			pins = "gpio28",
+			       "gpio29",
+			       "gpio30",
+			       "gpio31";
+			function = "alt4";
+		};
+	};
+	mii_gpio36: mii-gpio36 {
+		pins-mii {
+			pins = "gpio36",
+			       "gpio37",
+			       "gpio38",
+			       "gpio39";
+			function = "alt5";
+		};
+	};
+
+	pcm_gpio50: pcm-gpio50 {
+		pins-pcm {
+			pins = "gpio50",
+			       "gpio51",
+			       "gpio52",
+			       "gpio53";
+			function = "alt2";
+		};
+	};
+
+	pwm0_0_gpio12: pwm0-0-gpio12 {
+		pin-pwm {
+			pins = "gpio12";
+			function = "alt0";
+			bias-disable;
+		};
+	};
+	pwm0_0_gpio18: pwm0-0-gpio18 {
+		pin-pwm {
+			pins = "gpio18";
+			function = "alt5";
+			bias-disable;
+		};
+	};
+	pwm1_0_gpio40: pwm1-0-gpio40 {
+		pin-pwm {
+			pins = "gpio40";
+			function = "alt0";
+			bias-disable;
+		};
+	};
+	pwm0_1_gpio13: pwm0-1-gpio13 {
+		pin-pwm {
+			pins = "gpio13";
+			function = "alt0";
+			bias-disable;
+		};
+	};
+	pwm0_1_gpio19: pwm0-1-gpio19 {
+		pin-pwm {
+			pins = "gpio19";
+			function = "alt5";
+			bias-disable;
+		};
+	};
+	pwm1_1_gpio41: pwm1-1-gpio41 {
+		pin-pwm {
+			pins = "gpio41";
+			function = "alt0";
+			bias-disable;
+		};
+	};
+	pwm0_1_gpio45: pwm0-1-gpio45 {
+		pin-pwm {
+			pins = "gpio45";
+			function = "alt0";
+			bias-disable;
+		};
+	};
+	pwm0_0_gpio52: pwm0-0-gpio52 {
+		pin-pwm {
+			pins = "gpio52";
+			function = "alt1";
+			bias-disable;
+		};
+	};
+	pwm0_1_gpio53: pwm0-1-gpio53 {
+		pin-pwm {
+			pins = "gpio53";
+			function = "alt1";
+			bias-disable;
+		};
+	};
+
+	rgmii_gpio35: rgmii-gpio35 {
+		pin-start-stop {
+			pins = "gpio35";
+			function = "alt4";
+		};
+		pin-rx-ok {
+			pins = "gpio36";
+			function = "alt4";
+		};
+	};
+	rgmii_irq_gpio34: rgmii-irq-gpio34 {
+		pin-irq {
+			pins = "gpio34";
+			function = "alt5";
+		};
+	};
+	rgmii_irq_gpio39: rgmii-irq-gpio39 {
+		pin-irq {
+			pins = "gpio39";
+			function = "alt4";
+		};
+	};
+	rgmii_mdio_gpio28: rgmii-mdio-gpio28 {
+		pins-mdio {
+			pins = "gpio28",
+			       "gpio29";
+			function = "alt5";
+		};
+	};
+	rgmii_mdio_gpio37: rgmii-mdio-gpio37 {
+		pins-mdio {
+			pins = "gpio37",
+			       "gpio38";
+			function = "alt4";
+		};
+	};
+
+	spi0_gpio46: spi0-gpio46 {
+		pins-spi {
+			pins = "gpio46",
+			       "gpio47",
+			       "gpio48",
+			       "gpio49";
+			function = "alt2";
+		};
+	};
+	spi2_gpio46: spi2-gpio46 {
+		pins-spi {
+			pins = "gpio46",
+			       "gpio47",
+			       "gpio48",
+			       "gpio49",
+			       "gpio50";
+			function = "alt5";
+		};
+	};
+	spi3_gpio0: spi3-gpio0 {
+		pins-spi {
+			pins = "gpio0",
+			       "gpio1",
+			       "gpio2",
+			       "gpio3";
+			function = "alt3";
+		};
+	};
+	spi4_gpio4: spi4-gpio4 {
+		pins-spi {
+			pins = "gpio4",
+			       "gpio5",
+			       "gpio6",
+			       "gpio7";
+			function = "alt3";
+		};
+	};
+	spi5_gpio12: spi5-gpio12 {
+		pins-spi {
+			pins = "gpio12",
+			       "gpio13",
+			       "gpio14",
+			       "gpio15";
+			function = "alt3";
+		};
+	};
+	spi6_gpio18: spi6-gpio18 {
+		pins-spi {
+			pins = "gpio18",
+			       "gpio19",
+			       "gpio20",
+			       "gpio21";
+			function = "alt3";
+		};
+	};
+
+	uart2_gpio0: uart2-gpio0 {
+		pin-tx {
+			pins = "gpio0";
+			function = "alt4";
+			bias-disable;
+		};
+		pin-rx {
+			pins = "gpio1";
+			function = "alt4";
+			bias-pull-up;
+		};
+	};
+	uart2_ctsrts_gpio2: uart2-ctsrts-gpio2 {
+		pin-cts {
+			pins = "gpio2";
+			function = "alt4";
+			bias-pull-up;
+		};
+		pin-rts {
+			pins = "gpio3";
+			function = "alt4";
+			bias-disable;
+		};
+	};
+	uart3_gpio4: uart3-gpio4 {
+		pin-tx {
+			pins = "gpio4";
+			function = "alt4";
+			bias-disable;
+		};
+		pin-rx {
+			pins = "gpio5";
+			function = "alt4";
+			bias-pull-up;
+		};
+	};
+	uart3_ctsrts_gpio6: uart3-ctsrts-gpio6 {
+		pin-cts {
+			pins = "gpio6";
+			function = "alt4";
+			bias-pull-up;
+		};
+		pin-rts {
+			pins = "gpio7";
+			function = "alt4";
+			bias-disable;
+		};
+	};
+	uart4_gpio8: uart4-gpio8 {
+		pin-tx {
+			pins = "gpio8";
+			function = "alt4";
+			bias-disable;
+		};
+		pin-rx {
+			pins = "gpio9";
+			function = "alt4";
+			bias-pull-up;
+		};
+	};
+	uart4_ctsrts_gpio10: uart4-ctsrts-gpio10 {
+		pin-cts {
+			pins = "gpio10";
+			function = "alt4";
+			bias-pull-up;
+		};
+		pin-rts {
+			pins = "gpio11";
+			function = "alt4";
+			bias-disable;
+		};
+	};
+	uart5_gpio12: uart5-gpio12 {
+		pin-tx {
+			pins = "gpio12";
+			function = "alt4";
+			bias-disable;
+		};
+		pin-rx {
+			pins = "gpio13";
+			function = "alt4";
+			bias-pull-up;
+		};
+	};
+	uart5_ctsrts_gpio14: uart5-ctsrts-gpio14 {
+		pin-cts {
+			pins = "gpio14";
+			function = "alt4";
+			bias-pull-up;
+		};
+		pin-rts {
+			pins = "gpio15";
+			function = "alt4";
+			bias-disable;
+		};
+	};
+};
+
+&rmem {
+	#address-cells = <2>;
+};
+
+&cma {
+	/*
+	 * arm64 reserves the CMA by default somewhere in ZONE_DMA32,
+	 * that's not good enough for the BCM2711 as some devices can
+	 * only address the lower 1G of memory (ZONE_DMA).
+	 */
+	alloc-ranges = <0x0 0x00000000 0x40000000>;
+};
+
+&i2c0 {
+	compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
+	interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c1 {
+	compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
+	interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&mailbox {
+	interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&sdhci {
+	interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&sdhost {
+	interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&spi {
+	interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&spi1 {
+	interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&spi2 {
+	interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&system_timer {
+	interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&txp {
+	interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&uart0 {
+	interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&uart1 {
+	interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&usb {
+	interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&vec {
+	compatible = "brcm,bcm2711-vec";
+	interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/src/arm/broadcom/bcm28155-ap.dts b/src/arm/broadcom/bcm28155-ap.dts
new file mode 100644
index 0000000..2f36345
--- /dev/null
+++ b/src/arm/broadcom/bcm28155-ap.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2013 Broadcom Corporation
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "bcm11351.dtsi"
+
+/ {
+	model = "BCM28155 AP board";
+	compatible = "brcm,bcm28155-ap", "brcm,bcm11351";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>; /* 1 GB */
+	};
+};
+
+&bsc1 {
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&bsc2 {
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&bsc3 {
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&pmu_bsc {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	pmu: pmu@8 {
+		reg = <0x08>;
+	};
+};
+
+&pwm {
+	status = "okay";
+};
+
+&sdio2 {
+	non-removable;
+	max-frequency = <48000000>;
+	vmmc-supply = <&camldo1_reg>;
+	vqmmc-supply = <&iosr1_reg>;
+	status = "okay";
+};
+
+&sdio4 {
+	max-frequency = <48000000>;
+	cd-gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&sdldo_reg>;
+	vqmmc-supply = <&sdxldo_reg>;
+	status = "okay";
+};
+
+&uartb {
+	status = "okay";
+};
+
+&usbotg {
+	vusb_d-supply = <&usbldo_reg>;
+	vusb_a-supply = <&iosr1_reg>;
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+#include "bcm59056.dtsi"
+
+&pmu {
+	compatible = "brcm,bcm59056";
+	interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+	regulators {
+		camldo1_reg: camldo1 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		sdldo_reg: sdldo {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		sdxldo_reg: sdxldo {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		usbldo_reg: usbldo {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		iosr1_reg: iosr1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm2835-common.dtsi b/src/arm/broadcom/bcm2835-common.dtsi
new file mode 100644
index 0000000..9261b67
--- /dev/null
+++ b/src/arm/broadcom/bcm2835-common.dtsi
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* This include file covers the common peripherals and configuration between
+ * bcm2835, bcm2836 and bcm2837 implementations.
+ */
+
+/ {
+	interrupt-parent = <&intc>;
+
+	soc {
+		dma: dma-controller@7e007000 {
+			compatible = "brcm,bcm2835-dma";
+			reg = <0x7e007000 0xf00>;
+			interrupts = <1 16>,
+				     <1 17>,
+				     <1 18>,
+				     <1 19>,
+				     <1 20>,
+				     <1 21>,
+				     <1 22>,
+				     <1 23>,
+				     <1 24>,
+				     <1 25>,
+				     <1 26>,
+				     /* dma channel 11-14 share one irq */
+				     <1 27>,
+				     <1 27>,
+				     <1 27>,
+				     <1 27>,
+				     /* unused shared irq for all channels */
+				     <1 28>;
+			interrupt-names = "dma0",
+					  "dma1",
+					  "dma2",
+					  "dma3",
+					  "dma4",
+					  "dma5",
+					  "dma6",
+					  "dma7",
+					  "dma8",
+					  "dma9",
+					  "dma10",
+					  "dma11",
+					  "dma12",
+					  "dma13",
+					  "dma14",
+					  "dma-shared-all";
+			#dma-cells = <1>;
+			brcm,dma-channel-mask = <0x7f35>;
+		};
+
+		intc: interrupt-controller@7e00b200 {
+			compatible = "brcm,bcm2835-armctrl-ic";
+			reg = <0x7e00b200 0x200>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm: watchdog@7e100000 {
+			compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0x7e100000 0x114>,
+			      <0x7e00a000 0x24>;
+			reg-names = "pm", "asb";
+			clocks = <&clocks BCM2835_CLOCK_V3D>,
+				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
+				 <&clocks BCM2835_CLOCK_H264>,
+				 <&clocks BCM2835_CLOCK_ISP>;
+			clock-names = "v3d", "peri_image", "h264", "isp";
+			system-power-controller;
+		};
+
+		rng@7e104000 {
+			compatible = "brcm,bcm2835-rng";
+			reg = <0x7e104000 0x10>;
+			interrupts = <2 29>;
+		};
+
+		pixelvalve@7e206000 {
+			compatible = "brcm,bcm2835-pixelvalve0";
+			reg = <0x7e206000 0x100>;
+			interrupts = <2 13>; /* pwa0 */
+		};
+
+		pixelvalve@7e207000 {
+			compatible = "brcm,bcm2835-pixelvalve1";
+			reg = <0x7e207000 0x100>;
+			interrupts = <2 14>; /* pwa1 */
+		};
+
+		thermal: thermal@7e212000 {
+			compatible = "brcm,bcm2835-thermal";
+			reg = <0x7e212000 0x8>;
+			clocks = <&clocks BCM2835_CLOCK_TSENS>;
+			#thermal-sensor-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@7e805000 {
+			compatible = "brcm,bcm2835-i2c";
+			reg = <0x7e805000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+		};
+
+		vec: vec@7e806000 {
+			compatible = "brcm,bcm2835-vec";
+			reg = <0x7e806000 0x1000>;
+			clocks = <&clocks BCM2835_CLOCK_VEC>;
+			interrupts = <2 27>;
+			status = "disabled";
+		};
+
+		pixelvalve@7e807000 {
+			compatible = "brcm,bcm2835-pixelvalve2";
+			reg = <0x7e807000 0x100>;
+			interrupts = <2 10>; /* pixelvalve */
+		};
+
+		hdmi: hdmi@7e902000 {
+			compatible = "brcm,bcm2835-hdmi";
+			reg = <0x7e902000 0x600>,
+			      <0x7e808000 0x100>;
+			interrupts = <2 8>, <2 9>;
+			ddc = <&i2c2>;
+			clocks = <&clocks BCM2835_PLLH_PIX>,
+				 <&clocks BCM2835_CLOCK_HSM>;
+			clock-names = "pixel", "hdmi";
+			dmas = <&dma 17>;
+			dma-names = "audio-rx";
+			status = "disabled";
+		};
+
+		v3d: v3d@7ec00000 {
+			compatible = "brcm,bcm2835-v3d";
+			reg = <0x7ec00000 0x1000>;
+			interrupts = <1 10>;
+		};
+
+		vc4: gpu {
+			compatible = "brcm,bcm2835-vc4";
+		};
+	};
+};
+
+&cpu_thermal {
+	thermal-sensors = <&thermal>;
+};
+
+&gpio {
+	i2c_slave_gpio18: i2c-slave-gpio18 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	jtag_gpio4: jtag-gpio4 {
+		brcm,pins = <4 5 6 12 13>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+
+	pwm0_gpio12: pwm0-gpio12 {
+		brcm,pins = <12>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+	pwm0_gpio18: pwm0-gpio18 {
+		brcm,pins = <18>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	pwm0_gpio40: pwm0-gpio40 {
+		brcm,pins = <40>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+	pwm1_gpio13: pwm1-gpio13 {
+		brcm,pins = <13>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+	pwm1_gpio19: pwm1-gpio19 {
+		brcm,pins = <19>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+	};
+	pwm1_gpio41: pwm1-gpio41 {
+		brcm,pins = <41>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+	pwm1_gpio45: pwm1-gpio45 {
+		brcm,pins = <45>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+};
+
+&i2s {
+	dmas = <&dma 2>, <&dma 3>;
+	dma-names = "tx", "rx";
+};
+
+&sdhost {
+	dmas = <&dma 13>;
+	dma-names = "rx-tx";
+};
+
+&spi {
+	dmas = <&dma 6>, <&dma 7>;
+	dma-names = "tx", "rx";
+};
diff --git a/src/arm/broadcom/bcm2835-rpi-a-plus.dts b/src/arm/broadcom/bcm2835-rpi-a-plus.dts
new file mode 100644
index 0000000..069b482
--- /dev/null
+++ b/src/arm/broadcom/bcm2835-rpi-a-plus.dts
@@ -0,0 +1,130 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-a-plus", "brcm,bcm2835";
+	model = "Raspberry Pi Model A+";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x10000000>;
+	};
+};
+
+&gpio {
+	/*
+	 * This is based on the unreleased schematic for the Model A+.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "", /* GPIO30 */
+			  "", /* GPIO31 */
+			  "CAM_GPIO1", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "PWR_LOW_N", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "USB_LIMIT", /* GPIO38 */
+			  "", /* GPIO39 */
+			  "PWM0_OUT", /* GPIO40 */
+			  "CAM_GPIO0", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
+			  "PWM1_OUT", /* GPIO45 */
+			  "HDMI_HPD_N",
+			  "STATUS_LED",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
+
+	/* I2S interface */
+	i2s_alt0: i2s_alt0 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2835-rpi-a.dts b/src/arm/broadcom/bcm2835-rpi-a.dts
new file mode 100644
index 0000000..2726c00
--- /dev/null
+++ b/src/arm/broadcom/bcm2835-rpi-a.dts
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-a", "brcm,bcm2835";
+	model = "Raspberry Pi Model A";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x10000000>;
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf
+	 * RPI00021 sheet 02
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "CAM_GPIO1",
+			  "LAN_RUN",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "", /* GPIO12 */
+			  "", /* GPIO13 */
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "STATUS_LED_N",
+			  "GPIO17",
+			  "GPIO18",
+			  "", /* GPIO19 */
+			  "", /* GPIO20 */
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "", /* GPIO26 */
+			  "CAM_GPIO0",
+			  /* Binary number representing build/revision */
+			  "CONFIG0",
+			  "CONFIG1",
+			  "CONFIG2",
+			  "CONFIG3",
+			  "", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
+			  "PWM0_OUT",
+			  "", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
+			  "PWM1_OUT",
+			  "HDMI_HPD_P",
+			  "SD_CARD_DET",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
+
+	/* I2S interface */
+	i2s_alt2: i2s_alt2 {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <BCM2835_FSEL_ALT2>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2835-rpi-b-plus.dts b/src/arm/broadcom/bcm2835-rpi-b-plus.dts
new file mode 100644
index 0000000..c57b999
--- /dev/null
+++ b/src/arm/broadcom/bcm2835-rpi-b-plus.dts
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
+	model = "Raspberry Pi Model B+";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x20000000>;
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from Raspberry-Pi-B-Plus-V1.2-Schematics.pdf
+	 * RPI-BPLUS sheet 1
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "", /* GPIO30 */
+			  "LAN_RUN", /* GPIO31 */
+			  "CAM_GPIO1", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "PWR_LOW_N", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "USB_LIMIT", /* GPIO38 */
+			  "", /* GPIO39 */
+			  "PWM0_OUT", /* GPIO40 */
+			  "CAM_GPIO0", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "ETH_CLK", /* GPIO44 */
+			  "PWM1_OUT", /* GPIO45 */
+			  "HDMI_HPD_N",
+			  "STATUS_LED",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
+
+	/* I2S interface */
+	i2s_alt0: i2s_alt0 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2835-rpi-b-rev2.dts b/src/arm/broadcom/bcm2835-rpi-b-rev2.dts
new file mode 100644
index 0000000..ae6d3a9
--- /dev/null
+++ b/src/arm/broadcom/bcm2835-rpi-b-rev2.dts
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-smsc9512.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835";
+	model = "Raspberry Pi Model B rev2";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x10000000>;
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from Raspberry-Pi-Rev-2.0-Model-AB-Schematics.pdf
+	 * RPI00022 sheet 02
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "CAM_CLK",
+			  "LAN_RUN",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "", /* GPIO12 */
+			  "", /* GPIO13 */
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "STATUS_LED_N",
+			  "GPIO17",
+			  "GPIO18",
+			  "", /* GPIO19 */
+			  "", /* GPIO20 */
+			  "CAM_GPIO",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "", /* GPIO26 */
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
+			  "PWM0_OUT",
+			  "", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
+			  "PWM1_OUT",
+			  "HDMI_HPD_P",
+			  "SD_CARD_DET",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
+
+	/* I2S interface */
+	i2s_alt2: i2s_alt2 {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <BCM2835_FSEL_ALT2>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2835-rpi-b.dts b/src/arm/broadcom/bcm2835-rpi-b.dts
new file mode 100644
index 0000000..72764be
--- /dev/null
+++ b/src/arm/broadcom/bcm2835-rpi-b.dts
@@ -0,0 +1,117 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-smsc9512.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b", "brcm,bcm2835";
+	model = "Raspberry Pi Model B";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x10000000>;
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf
+	 * RPI00021 sheet 02
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "CAM_GPIO1",
+			  "LAN_RUN",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "", /* GPIO12 */
+			  "", /* GPIO13 */
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "STATUS_LED_N",
+			  "GPIO17",
+			  "GPIO18",
+			  "", /* GPIO19 */
+			  "", /* GPIO20 */
+			  "CAM_GPIO0",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "", /* GPIO26 */
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
+			  "PWM0_OUT",
+			  "", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
+			  "PWM1_OUT",
+			  "HDMI_HPD_P",
+			  "SD_CARD_DET",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2835-rpi-cm1-io1.dts b/src/arm/broadcom/bcm2835-rpi-cm1-io1.dts
new file mode 100644
index 0000000..3f9d198
--- /dev/null
+++ b/src/arm/broadcom/bcm2835-rpi-cm1-io1.dts
@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835-rpi-cm1.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+	model = "Raspberry Pi Compute Module IO board rev1";
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "GPIO0",
+			  "GPIO1",
+			  "GPIO2",
+			  "GPIO3",
+			  "GPIO4",
+			  "GPIO5",
+			  "GPIO6",
+			  "GPIO7",
+			  "GPIO8",
+			  "GPIO9",
+			  "GPIO10",
+			  "GPIO11",
+			  "GPIO12",
+			  "GPIO13",
+			  "GPIO14",
+			  "GPIO15",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "GPIO32",
+			  "GPIO33",
+			  "GPIO34",
+			  "GPIO35",
+			  "GPIO36",
+			  "GPIO37",
+			  "GPIO38",
+			  "GPIO39",
+			  "GPIO40",
+			  "GPIO41",
+			  "GPIO42",
+			  "GPIO43",
+			  "GPIO44",
+			  "GPIO45",
+			  "HDMI_HPD_N",
+			  /* Also used as ACT LED */
+			  "EMMC_EN_N",
+			  /* Used by eMMC */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2835-rpi-cm1.dtsi b/src/arm/broadcom/bcm2835-rpi-cm1.dtsi
new file mode 100644
index 0000000..750cd76
--- /dev/null
+++ b/src/arm/broadcom/bcm2835-rpi-cm1.dtsi
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+
+/ {
+	leds {
+		led-act {
+			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x20000000>;
+	};
+
+	reg_3v3: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_1v8: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+};
+
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+};
+
+&sdhost {
+	non-removable;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_1v8>;
+};
diff --git a/src/arm/broadcom/bcm2835-rpi-common.dtsi b/src/arm/broadcom/bcm2835-rpi-common.dtsi
new file mode 100644
index 0000000..4e7b4a5
--- /dev/null
+++ b/src/arm/broadcom/bcm2835-rpi-common.dtsi
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * This include file covers the common peripherals and configuration between
+ * bcm2835, bcm2836 and bcm2837 implementations that interact with RPi's
+ * firmware interface.
+ */
+
+#include <dt-bindings/power/raspberrypi-power.h>
+
+&firmware {
+	firmware_clocks: clocks {
+		compatible = "raspberrypi,firmware-clocks";
+		#clock-cells = <1>;
+	};
+};
+
+&hdmi {
+	clocks = <&firmware_clocks 9>,
+		 <&firmware_clocks 13>;
+	clock-names = "pixel", "hdmi";
+};
+
+&v3d {
+	power-domains = <&power RPI_POWER_DOMAIN_V3D>;
+};
+
+&vec {
+	clocks = <&firmware_clocks 15>;
+};
diff --git a/src/arm/broadcom/bcm2835-rpi-zero-w.dts b/src/arm/broadcom/bcm2835-rpi-zero-w.dts
new file mode 100644
index 0000000..1f0b163
--- /dev/null
+++ b/src/arm/broadcom/bcm2835-rpi-zero-w.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-usb-otg.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
+	model = "Raspberry Pi Zero W";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x20000000>;
+	};
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+};
+
+&bt {
+	shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "CAM_GPIO1", /* GPIO40 */
+			  "WL_ON", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "WIFI_CLK", /* GPIO43 */
+			  "CAM_GPIO0", /* GPIO44 */
+			  "BT_ON", /* GPIO45 */
+			  "HDMI_HPD_N",
+			  "STATUS_LED_N",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+};
+
+&sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&wifi_pwrseq {
+	reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+};
diff --git a/src/arm/broadcom/bcm2835-rpi-zero.dts b/src/arm/broadcom/bcm2835-rpi-zero.dts
new file mode 100644
index 0000000..539c19c
--- /dev/null
+++ b/src/arm/broadcom/bcm2835-rpi-zero.dts
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-usb-otg.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero", "brcm,bcm2835";
+	model = "Raspberry Pi Zero";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x20000000>;
+	};
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "", /* GPIO30 */
+			  "", /* GPIO31 */
+			  "CAM_GPIO1", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
+			  "", /* GPIO40 */
+			  "CAM_GPIO0", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
+			  "", /* GPIO45 */
+			  "HDMI_HPD_N",
+			  "STATUS_LED_N",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
+
+	/* I2S interface */
+	i2s_alt0: i2s_alt0 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2835-rpi.dtsi b/src/arm/broadcom/bcm2835-rpi.dtsi
new file mode 100644
index 0000000..f0acc93
--- /dev/null
+++ b/src/arm/broadcom/bcm2835-rpi.dtsi
@@ -0,0 +1,69 @@
+#include <dt-bindings/power/raspberrypi-power.h>
+
+/ {
+	soc {
+		firmware: firmware {
+			compatible = "raspberrypi,bcm2835-firmware", "simple-mfd";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			mboxes = <&mailbox>;
+			dma-ranges;
+		};
+
+		power: power {
+			compatible = "raspberrypi,bcm2835-power";
+			firmware = <&firmware>;
+			#power-domain-cells = <1>;
+		};
+
+		vchiq: mailbox@7e00b840 {
+			compatible = "brcm,bcm2835-vchiq";
+			reg = <0x7e00b840 0x3c>;
+			interrupts = <0 2>;
+		};
+	};
+};
+
+&gpio {
+	gpioout: gpioout {
+		brcm,pins = <6>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	alt0: alt0 {
+		brcm,pins = <4 5 7 8 9 10 11>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_gpio0>;
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_gpio2>;
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+&usb {
+	power-domains = <&power RPI_POWER_DOMAIN_USB>;
+};
+
+&vec {
+	power-domains = <&power RPI_POWER_DOMAIN_VEC>;
+	status = "okay";
+};
+
+&dsi0 {
+	power-domains = <&power RPI_POWER_DOMAIN_DSI0>;
+};
+
+&dsi1 {
+	power-domains = <&power RPI_POWER_DOMAIN_DSI1>;
+};
diff --git a/src/arm/broadcom/bcm2835.dtsi b/src/arm/broadcom/bcm2835.dtsi
new file mode 100644
index 0000000..15cb331
--- /dev/null
+++ b/src/arm/broadcom/bcm2835.dtsi
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm283x.dtsi"
+#include "bcm2835-common.dtsi"
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,arm1176jzf-s";
+			reg = <0x0>;
+			/* Source for d/i-cache-line-size and d/i-cache-sets
+			 * https://developer.arm.com/documentation/ddi0301
+			 * /h/level-one-memory-system/cache-organization?lang=en
+			 *
+			 * Source for d/i-cache-size
+			 * https://forums.raspberrypi.com/viewtopic.php?t=98428
+			 *
+			 * NOTE: The BCM2835 has a L2 cache but it is dedicated to the GPU
+			 * It can be shared with the CPU through fw settings,
+			 * but this is not recommended.
+			 */
+			d-cache-size = <0x4000>;
+			d-cache-line-size = <16>;
+			d-cache-sets = <256>; // 16KiB(size)/16(line-size)=1024ways/4-way set
+			i-cache-size = <0x4000>;
+			i-cache-line-size = <16>;
+			i-cache-sets = <256>; // 16KiB(size)/16(line-size)=1024ways/4-way set
+		};
+	};
+
+	soc {
+		ranges = <0x7e000000 0x20000000 0x02000000>;
+		dma-ranges = <0x40000000 0x00000000 0x20000000>;
+	};
+
+	arm-pmu {
+		compatible = "arm,arm1176-pmu";
+	};
+};
+
+&cpu_thermal {
+	coefficients = <(-538)	407000>;
+};
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+	compatible = "brcm,bcm2835-thermal";
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2836-rpi-2-b.dts b/src/arm/broadcom/bcm2836-rpi-2-b.dts
new file mode 100644
index 0000000..7991803
--- /dev/null
+++ b/src/arm/broadcom/bcm2836-rpi-2-b.dts
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2836.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
+	model = "Raspberry Pi 2 Model B";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x40000000>;
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from rpi_SCH_2b_1p2_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "", /* GPIO30 */
+			  "LAN_RUN",
+			  "CAM_GPIO1",
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "PWR_LOW_N",
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "USB_LIMIT",
+			  "", /* GPIO39 */
+			  "PWM0_OUT",
+			  "CAM_GPIO0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  "ETH_CLK",
+			  "PWM1_OUT",
+			  "HDMI_HPD_N",
+			  "STATUS_LED",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
+
+	/* I2S interface */
+	i2s_alt0: i2s_alt0 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2836-rpi.dtsi b/src/arm/broadcom/bcm2836-rpi.dtsi
new file mode 100644
index 0000000..48b03b5
--- /dev/null
+++ b/src/arm/broadcom/bcm2836-rpi.dtsi
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+
+&vchiq {
+	compatible = "brcm,bcm2836-vchiq", "brcm,bcm2835-vchiq";
+};
diff --git a/src/arm/broadcom/bcm2836.dtsi b/src/arm/broadcom/bcm2836.dtsi
new file mode 100644
index 0000000..783fe62
--- /dev/null
+++ b/src/arm/broadcom/bcm2836.dtsi
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm283x.dtsi"
+#include "bcm2835-common.dtsi"
+
+/ {
+	compatible = "brcm,bcm2836";
+
+	soc {
+		ranges = <0x7e000000 0x3f000000 0x1000000>,
+			 <0x40000000 0x40000000 0x00001000>;
+		dma-ranges = <0xc0000000 0x00000000 0x3f000000>;
+
+		local_intc: interrupt-controller@40000000 {
+			compatible = "brcm,bcm2836-l1-intc";
+			reg = <0x40000000 0x100>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&local_intc>;
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupt-parent = <&local_intc>;
+		interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupt-parent = <&local_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, // PHYS_SECURE_PPI
+			     <1 IRQ_TYPE_LEVEL_HIGH>, // PHYS_NONSECURE_PPI
+			     <3 IRQ_TYPE_LEVEL_HIGH>, // VIRT_PPI
+			     <2 IRQ_TYPE_LEVEL_HIGH>; // HYP_PPI
+		always-on;
+	};
+
+	cpus: cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "brcm,bcm2836-smp";
+
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 * https://developer.arm.com/documentation/ddi0464/f/L1-Memory-System
+		 * /About-the-L1-memory-system?lang=en
+		 *
+		 * Source for d/i-cache-size
+		 * https://forums.raspberrypi.com/viewtopic.php?t=98428
+		 */
+
+		v7_cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf00>;
+			clock-frequency = <800000000>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <32>;
+			i-cache-sets = <512>; // 32KiB(size)/32(line-size)=1024ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		v7_cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf01>;
+			clock-frequency = <800000000>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <32>;
+			i-cache-sets = <512>; // 32KiB(size)/32(line-size)=1024ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		v7_cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf02>;
+			clock-frequency = <800000000>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <32>;
+			i-cache-sets = <512>; // 32KiB(size)/32(line-size)=1024ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		v7_cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf03>;
+			clock-frequency = <800000000>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <32>;
+			i-cache-sets = <512>; // 32KiB(size)/32(line-size)=1024ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		/* Source for cache-line-size + cache-sets
+		 * https://developer.arm.com/documentation/ddi0464/f/L2-Memory-System
+		 * /About-the-L2-Memory-system?lang=en
+		 * Source for cache-size
+		 * https://forums.raspberrypi.com/viewtopic.php?t=98428
+		 */
+		l2: l2-cache0 {
+			compatible = "cache";
+			cache-unified;
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>; // 512KiB(size)/64(line-size)=8192ways/8-way set
+			cache-level = <2>;
+		};
+	};
+};
+
+/* Make the BCM2835-style global interrupt controller be a child of the
+ * CPU-local interrupt controller.
+ */
+&intc {
+	compatible = "brcm,bcm2836-armctrl-ic";
+	reg = <0x7e00b200 0x200>;
+	interrupt-parent = <&local_intc>;
+	interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&cpu_thermal {
+	coefficients = <(-538)	407000>;
+};
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+	compatible = "brcm,bcm2836-thermal";
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2837-rpi-3-a-plus.dts b/src/arm/broadcom/bcm2837-rpi-3-a-plus.dts
new file mode 100644
index 0000000..3548306
--- /dev/null
+++ b/src/arm/broadcom/bcm2837-rpi-3-a-plus.dts
@@ -0,0 +1,158 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model A+";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x20000000>;
+	};
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "",
+				  "BT_WL_ON",
+				  "STATUS_LED_R",
+				  "",
+				  "",
+				  "CAM_GPIO0",
+				  "CAM_GPIO1",
+				  "";
+		status = "okay";
+	};
+};
+
+&gpio {
+	/*
+	 * This is mostly based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "HDMI_HPD_N",
+			  "STATUS_LED_G",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "", /* GPIO42 */
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+	status = "okay";
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	status = "okay";
+	bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module
+ *
+ * WL_REG_ON and BT_REG_ON of the CYW43455 Wifi/BT module are driven
+ * by a single GPIO. We can't give GPIO control to one of the drivers,
+ * otherwise the other part would get unexpectedly disturbed.
+ */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2837-rpi-3-b-plus.dts b/src/arm/broadcom/bcm2837-rpi-3-b-plus.dts
new file mode 100644
index 0000000..2f1800c
--- /dev/null
+++ b/src/arm/broadcom/bcm2837-rpi-3-b-plus.dts
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-lan7515.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model B+";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x40000000>;
+	};
+};
+
+&bt {
+	shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "BT_ON",
+				  "WL_ON",
+				  "PWR_LED_R",
+				  "LAN_RUN",
+				  "",
+				  "CAM_GPIO0",
+				  "CAM_GPIO1",
+				  "";
+		status = "okay";
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from rpi_SCH_3bplus_1p0_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "HDMI_HPD_N",
+			  "STATUS_LED_G",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "ETH_CLK",
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+	status = "okay";
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	status = "okay";
+	bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&wifi_pwrseq {
+	reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
diff --git a/src/arm/broadcom/bcm2837-rpi-3-b.dts b/src/arm/broadcom/bcm2837-rpi-3-b.dts
new file mode 100644
index 0000000..6127034
--- /dev/null
+++ b/src/arm/broadcom/bcm2837-rpi-3-b.dts
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model B";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x40000000>;
+	};
+};
+
+&bt {
+	shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "BT_ON",
+				  "WL_ON",
+				  "STATUS_LED",
+				  "LAN_RUN",
+				  "HDMI_HPD_N",
+				  "CAM_GPIO0",
+				  "CAM_GPIO1",
+				  "PWR_LOW_N";
+		status = "okay";
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from rpi_SCH_3b_1p2_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "", /* GPIO 28 */
+			  "LAN_RUN_BOOT",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "ETH_CLK",
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+	status = "okay";
+};
+
+&hdmi {
+	hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	status = "okay";
+	bus-width = <4>;
+};
+
+&wifi_pwrseq {
+	reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
diff --git a/src/arm/broadcom/bcm2837-rpi-cm3-io3.dts b/src/arm/broadcom/bcm2837-rpi-cm3-io3.dts
new file mode 100644
index 0000000..72d26d1
--- /dev/null
+++ b/src/arm/broadcom/bcm2837-rpi-cm3-io3.dts
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837-rpi-cm3.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-compute-module", "brcm,bcm2837";
+	model = "Raspberry Pi Compute Module 3 IO board V3.0";
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "GPIO0",
+			  "GPIO1",
+			  "GPIO2",
+			  "GPIO3",
+			  "GPIO4",
+			  "GPIO5",
+			  "GPIO6",
+			  "GPIO7",
+			  "GPIO8",
+			  "GPIO9",
+			  "GPIO10",
+			  "GPIO11",
+			  "GPIO12",
+			  "GPIO13",
+			  "GPIO14",
+			  "GPIO15",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "GPIO32",
+			  "GPIO33",
+			  "GPIO34",
+			  "GPIO35",
+			  "GPIO36",
+			  "GPIO37",
+			  "GPIO38",
+			  "GPIO39",
+			  "GPIO40",
+			  "GPIO41",
+			  "GPIO42",
+			  "GPIO43",
+			  "GPIO44",
+			  "GPIO45",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by eMMC */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+	hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2837-rpi-cm3.dtsi b/src/arm/broadcom/bcm2837-rpi-cm3.dtsi
new file mode 100644
index 0000000..1e4e494
--- /dev/null
+++ b/src/arm/broadcom/bcm2837-rpi-cm3.dtsi
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+
+/ {
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x40000000>;
+	};
+
+	reg_3v3: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_1v8: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "HDMI_HPD_N",
+				  "EMMC_EN_N",
+				  "",
+				  "",
+				  "",
+				  "",
+				  "",
+				  "";
+		status = "okay";
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_1v8>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm2837-rpi-zero-2-w.dts b/src/arm/broadcom/bcm2837-rpi-zero-2-w.dts
new file mode 100644
index 0000000..85cf594
--- /dev/null
+++ b/src/arm/broadcom/bcm2837-rpi-zero-2-w.dts
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2022 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-usb-otg.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero-2-w", "brcm,bcm2837";
+	model = "Raspberry Pi Zero 2 W";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x20000000>;
+	};
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+};
+
+&bt {
+	shutdown-gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "HDMI_HPD_N",
+			  "STATUS_LED_N",
+			  "NC", /* GPIO30 */
+			  "NC", /* GPIO31 */
+			  "NC", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "NC", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "CAM_GPIO0", /* GPIO40 */
+			  "WL_ON", /* GPIO41 */
+			  "BT_ON", /* GPIO42 */
+			  "WIFI_CLK", /* GPIO43 */
+			  "SDA0", /* GPIO44 */
+			  "SCL0", /* GPIO45 */
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
+};
+
+&sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&wifi_pwrseq {
+	reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+};
diff --git a/src/arm/broadcom/bcm2837.dtsi b/src/arm/broadcom/bcm2837.dtsi
new file mode 100644
index 0000000..84c08b4
--- /dev/null
+++ b/src/arm/broadcom/bcm2837.dtsi
@@ -0,0 +1,144 @@
+#include "bcm283x.dtsi"
+#include "bcm2835-common.dtsi"
+
+/ {
+	compatible = "brcm,bcm2837";
+
+	soc {
+		ranges = <0x7e000000 0x3f000000 0x1000000>,
+			 <0x40000000 0x40000000 0x00001000>;
+		dma-ranges = <0xc0000000 0x00000000 0x3f000000>;
+
+		local_intc: local_intc@40000000 {
+			compatible = "brcm,bcm2836-l1-intc";
+			reg = <0x40000000 0x100>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&local_intc>;
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupt-parent = <&local_intc>;
+		interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupt-parent = <&local_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, // PHYS_SECURE_PPI
+			     <1 IRQ_TYPE_LEVEL_HIGH>, // PHYS_NONSECURE_PPI
+			     <3 IRQ_TYPE_LEVEL_HIGH>, // VIRT_PPI
+			     <2 IRQ_TYPE_LEVEL_HIGH>; // HYP_PPI
+		always-on;
+	};
+
+	cpus: cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
+
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 * https://developer.arm.com/documentation/ddi0500/e/level-1-memory-system
+		 * /about-the-l1-memory-system?lang=en
+		 *
+		 * Source for d/i-cache-size
+		 * https://magpi.raspberrypi.com/articles/raspberry-pi-3-specs-benchmarks
+		 */
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000d8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <1>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000e0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <2>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000e8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <3>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x000000f0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		/* Source for cache-line-size + cache-sets
+		 * https://developer.arm.com/documentation/ddi0500
+		 * /e/level-2-memory-system/about-the-l2-memory-system?lang=en
+		 * Source for cache-size
+		 * https://datasheets.raspberrypi.com/cm/cm1-and-cm3-datasheet.pdf
+		 */
+		l2: l2-cache0 {
+			compatible = "cache";
+			cache-unified;
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>; // 512KiB(size)/64(line-size)=8192ways/16-way set
+			cache-level = <2>;
+		};
+	};
+};
+
+/* Make the BCM2835-style global interrupt controller be a child of the
+ * CPU-local interrupt controller.
+ */
+&intc {
+	compatible = "brcm,bcm2836-armctrl-ic";
+	reg = <0x7e00b200 0x200>;
+	interrupt-parent = <&local_intc>;
+	interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&cpu_thermal {
+	coefficients = <(-538)	412000>;
+};
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+	compatible = "brcm,bcm2837-thermal";
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm283x-rpi-lan7515.dtsi b/src/arm/broadcom/bcm283x-rpi-lan7515.dtsi
new file mode 100644
index 0000000..70bece6
--- /dev/null
+++ b/src/arm/broadcom/bcm283x-rpi-lan7515.dtsi
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/net/microchip-lan78xx.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet;
+	};
+};
+
+&usb {
+	usb-port@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usb-port@1 {
+			compatible = "usb424,2514";
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethernet: ethernet@1 {
+				compatible = "usb424,7800";
+				reg = <1>;
+
+				mdio {
+					#address-cells = <0x1>;
+					#size-cells = <0x0>;
+					eth_phy: ethernet-phy@1 {
+						reg = <1>;
+						microchip,led-modes = <
+							LAN78XX_LINK_1000_ACTIVITY
+							LAN78XX_LINK_10_100_ACTIVITY
+						>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm283x-rpi-led-deprecated.dtsi b/src/arm/broadcom/bcm283x-rpi-led-deprecated.dtsi
new file mode 100644
index 0000000..f83e56d
--- /dev/null
+++ b/src/arm/broadcom/bcm283x-rpi-led-deprecated.dtsi
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	/*
+	 * This file provides the now deprecated ACT LED to the
+	 * Raspberry Pi boards. Please don't include this file
+	 * for new boards!
+	 */
+	leds: leds {
+		compatible = "gpio-leds";
+
+		led_act: led-act {
+			label = "ACT";
+			default-state = "keep";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm283x-rpi-smsc9512.dtsi b/src/arm/broadcom/bcm283x-rpi-smsc9512.dtsi
new file mode 100644
index 0000000..882b138
--- /dev/null
+++ b/src/arm/broadcom/bcm283x-rpi-smsc9512.dtsi
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	aliases {
+		ethernet0 = &ethernet;
+	};
+};
+
+&usb {
+	usb1@1 {
+		compatible = "usb424,9512";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethernet: ethernet@1 {
+			compatible = "usb424,ec00";
+			reg = <1>;
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm283x-rpi-smsc9514.dtsi b/src/arm/broadcom/bcm283x-rpi-smsc9514.dtsi
new file mode 100644
index 0000000..4273b90
--- /dev/null
+++ b/src/arm/broadcom/bcm283x-rpi-smsc9514.dtsi
@@ -0,0 +1,19 @@
+/ {
+	aliases {
+		ethernet0 = &ethernet;
+	};
+};
+
+&usb {
+	usb1@1 {
+		compatible = "usb424,9514";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethernet: ethernet@1 {
+			compatible = "usb424,ec00";
+			reg = <1>;
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm283x-rpi-usb-host.dtsi b/src/arm/broadcom/bcm283x-rpi-usb-host.dtsi
new file mode 100644
index 0000000..73f4ece
--- /dev/null
+++ b/src/arm/broadcom/bcm283x-rpi-usb-host.dtsi
@@ -0,0 +1,3 @@
+&usb {
+	dr_mode = "host";
+};
diff --git a/src/arm/broadcom/bcm283x-rpi-usb-otg.dtsi b/src/arm/broadcom/bcm283x-rpi-usb-otg.dtsi
new file mode 100644
index 0000000..e2fd961
--- /dev/null
+++ b/src/arm/broadcom/bcm283x-rpi-usb-otg.dtsi
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0
+&usb {
+	dr_mode = "otg";
+	g-rx-fifo-size = <256>;
+	g-np-tx-fifo-size = <32>;
+	/*
+	 * According to dwc2 the sum of all device EP
+	 * fifo sizes shouldn't exceed 3776 bytes.
+	 */
+	g-tx-fifo-size = <256 256 512 512 512 768 768>;
+};
diff --git a/src/arm/broadcom/bcm283x-rpi-usb-peripheral.dtsi b/src/arm/broadcom/bcm283x-rpi-usb-peripheral.dtsi
new file mode 100644
index 0000000..0ff0e9e
--- /dev/null
+++ b/src/arm/broadcom/bcm283x-rpi-usb-peripheral.dtsi
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
+&usb {
+	dr_mode = "peripheral";
+	g-rx-fifo-size = <256>;
+	g-np-tx-fifo-size = <32>;
+	g-tx-fifo-size = <256 256 512 512 512 768 768>;
+};
diff --git a/src/arm/broadcom/bcm283x-rpi-wifi-bt.dtsi b/src/arm/broadcom/bcm283x-rpi-wifi-bt.dtsi
new file mode 100644
index 0000000..0b64cc1
--- /dev/null
+++ b/src/arm/broadcom/bcm283x-rpi-wifi-bt.dtsi
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+	};
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34>;
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	status = "okay";
+
+	bt: bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+	};
+};
diff --git a/src/arm/broadcom/bcm283x.dtsi b/src/arm/broadcom/bcm283x.dtsi
new file mode 100644
index 0000000..2ca8a25
--- /dev/null
+++ b/src/arm/broadcom/bcm283x.dtsi
@@ -0,0 +1,501 @@
+#include <dt-bindings/pinctrl/bcm2835.h>
+#include <dt-bindings/clock/bcm2835.h>
+#include <dt-bindings/clock/bcm2835-aux.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/soc/bcm2835-pm.h>
+
+/* firmware-provided startup stubs live here, where the secondary CPUs are
+ * spinning.
+ */
+/memreserve/ 0x00000000 0x00001000;
+
+/* This include file covers the common peripherals and configuration between
+ * bcm2835 and bcm2836 implementations, leaving the CPU configuration to
+ * bcm2835.dtsi and bcm2836.dtsi.
+ */
+
+/ {
+	compatible = "brcm,bcm2835";
+	model = "BCM2835";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	rmem: reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		cma: linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x4000000>; /* 64MB */
+			reusable;
+			linux,cma-default;
+		};
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+
+			trips {
+				cpu-crit {
+					temperature = <90000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+			};
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		system_timer: timer@7e003000 {
+			compatible = "brcm,bcm2835-system-timer";
+			reg = <0x7e003000 0x1000>;
+			interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
+			/* This could be a reference to BCM2835_CLOCK_TIMER,
+			 * but we don't have the driver using the common clock
+			 * support yet.
+			 */
+			clock-frequency = <1000000>;
+		};
+
+		txp: txp@7e004000 {
+			compatible = "brcm,bcm2835-txp";
+			reg = <0x7e004000 0x20>;
+			interrupts = <1 11>;
+		};
+
+		clocks: cprman@7e101000 {
+			compatible = "brcm,bcm2835-cprman";
+			#clock-cells = <1>;
+			reg = <0x7e101000 0x2000>;
+
+			/* CPRMAN derives almost everything from the
+			 * platform's oscillator.  However, the DSI
+			 * pixel clocks come from the DSI analog PHY.
+			 */
+			clocks = <&clk_osc>,
+				<&dsi0 0>, <&dsi0 1>, <&dsi0 2>,
+				<&dsi1 0>, <&dsi1 1>, <&dsi1 2>;
+		};
+
+		mailbox: mailbox@7e00b880 {
+			compatible = "brcm,bcm2835-mbox";
+			reg = <0x7e00b880 0x40>;
+			interrupts = <0 1>;
+			#mbox-cells = <0>;
+		};
+
+		gpio: gpio@7e200000 {
+			compatible = "brcm,bcm2835-gpio";
+			reg = <0x7e200000 0xb4>;
+			/*
+			 * The GPIO IP block is designed for 3 banks of GPIOs.
+			 * Each bank has a GPIO interrupt for itself.
+			 * There is an overall "any bank" interrupt.
+			 * In order, these are GIC interrupts 17, 18, 19, 20.
+			 * Since the BCM2835 only has 2 banks, the 2nd bank
+			 * interrupt output appears to be mirrored onto the
+			 * 3rd bank's interrupt signal.
+			 * So, a bank0 interrupt shows up on 17, 20, and
+			 * a bank1 interrupt shows up on 18, 19, 20!
+			 */
+			interrupts = <2 17>, <2 18>, <2 19>, <2 20>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			gpio-ranges = <&gpio 0 0 54>;
+
+			/* Defines common pin muxing groups
+			 *
+			 * While each pin can have its mux selected
+			 * for various functions individually, some
+			 * groups only make sense to switch to a
+			 * particular function together.
+			 */
+			dpi_gpio0: dpi-gpio0 {
+				brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
+					     12 13 14 15 16 17 18 19
+					     20 21 22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			emmc_gpio22: emmc-gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			emmc_gpio34: emmc-gpio34 {
+				brcm,pins = <34 35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+				brcm,pull = <BCM2835_PUD_OFF
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP>;
+			};
+			emmc_gpio48: emmc-gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+
+			gpclk0_gpio4: gpclk0-gpio4 {
+				brcm,pins = <4>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio5: gpclk1-gpio5 {
+				brcm,pins = <5>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio42: gpclk1-gpio42 {
+				brcm,pins = <42>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio44: gpclk1-gpio44 {
+				brcm,pins = <44>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio6: gpclk2-gpio6 {
+				brcm,pins = <6>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio43: gpclk2-gpio43 {
+				brcm,pins = <43>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+				brcm,pull = <BCM2835_PUD_OFF>;
+			};
+
+			i2c0_gpio0: i2c0-gpio0 {
+				brcm,pins = <0 1>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio28: i2c0-gpio28 {
+				brcm,pins = <28 29>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio44: i2c0-gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT1>;
+			};
+			i2c1_gpio2: i2c1-gpio2 {
+				brcm,pins = <2 3>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c1_gpio44: i2c1-gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+
+			jtag_gpio22: jtag-gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+
+			pcm_gpio18: pcm-gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pcm_gpio28: pcm-gpio28 {
+				brcm,pins = <28 29 30 31>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+
+			sdhost_gpio48: sdhost-gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+
+			spi0_gpio7: spi0-gpio7 {
+				brcm,pins = <7 8 9 10 11>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spi0_gpio35: spi0-gpio35 {
+				brcm,pins = <35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spi1_gpio16: spi1-gpio16 {
+				brcm,pins = <16 17 18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			spi2_gpio40: spi2-gpio40 {
+				brcm,pins = <40 41 42 43 44 45>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+
+			uart0_gpio14: uart0-gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			/* Separate from the uart0_gpio14 group
+			 * because it conflicts with spi1_gpio16, and
+			 * people often run uart0 on the two pins
+			 * without flow control.
+			 */
+			uart0_ctsrts_gpio16: uart0-ctsrts-gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_ctsrts_gpio30: uart0-ctsrts-gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+				brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>;
+			};
+			uart0_gpio32: uart0-gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+				brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>;
+			};
+			uart0_gpio36: uart0-gpio36 {
+				brcm,pins = <36 37>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			uart0_ctsrts_gpio38: uart0-ctsrts-gpio38 {
+				brcm,pins = <38 39>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+
+			uart1_gpio14: uart1-gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio16: uart1-ctsrts-gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio32: uart1-gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio30: uart1-ctsrts-gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio40: uart1-gpio40 {
+				brcm,pins = <40 41>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio42: uart1-ctsrts-gpio42 {
+				brcm,pins = <42 43>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+		};
+
+		uart0: serial@7e201000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201000 0x200>;
+			interrupts = <2 25>;
+			clocks = <&clocks BCM2835_CLOCK_UART>,
+				 <&clocks BCM2835_CLOCK_VPU>;
+			clock-names = "uartclk", "apb_pclk";
+			arm,primecell-periphid = <0x00241011>;
+		};
+
+		sdhost: mmc@7e202000 {
+			compatible = "brcm,bcm2835-sdhost";
+			reg = <0x7e202000 0x100>;
+			interrupts = <2 24>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			status = "disabled";
+		};
+
+		i2s: i2s@7e203000 {
+			compatible = "brcm,bcm2835-i2s";
+			reg = <0x7e203000 0x24>;
+			clocks = <&clocks BCM2835_CLOCK_PCM>;
+			status = "disabled";
+		};
+
+		spi: spi@7e204000 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204000 0x200>;
+			interrupts = <2 22>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c0: i2c@7e205000 {
+			compatible = "brcm,bcm2835-i2c";
+			reg = <0x7e205000 0x200>;
+			interrupts = <2 21>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		dpi: dpi@7e208000 {
+			compatible = "brcm,bcm2835-dpi";
+			reg = <0x7e208000 0x8c>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>,
+				 <&clocks BCM2835_CLOCK_DPI>;
+			clock-names = "core", "pixel";
+			status = "disabled";
+		};
+
+		dsi0: dsi@7e209000 {
+			compatible = "brcm,bcm2835-dsi0";
+			reg = <0x7e209000 0x78>;
+			interrupts = <2 4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+
+			clocks = <&clocks BCM2835_PLLA_DSI0>,
+				 <&clocks BCM2835_CLOCK_DSI0E>,
+				 <&clocks BCM2835_CLOCK_DSI0P>;
+			clock-names = "phy", "escape", "pixel";
+
+			clock-output-names = "dsi0_byte",
+					     "dsi0_ddr2",
+					     "dsi0_ddr";
+
+			status = "disabled";
+		};
+
+		aux: aux@7e215000 {
+			compatible = "brcm,bcm2835-aux";
+			#clock-cells = <1>;
+			reg = <0x7e215000 0x8>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+		};
+
+		uart1: serial@7e215040 {
+			compatible = "brcm,bcm2835-aux-uart";
+			reg = <0x7e215040 0x40>;
+			interrupts = <1 29>;
+			clocks = <&aux BCM2835_AUX_CLOCK_UART>;
+			status = "disabled";
+		};
+
+		spi1: spi@7e215080 {
+			compatible = "brcm,bcm2835-aux-spi";
+			reg = <0x7e215080 0x40>;
+			interrupts = <1 29>;
+			clocks = <&aux BCM2835_AUX_CLOCK_SPI1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi2: spi@7e2150c0 {
+			compatible = "brcm,bcm2835-aux-spi";
+			reg = <0x7e2150c0 0x40>;
+			interrupts = <1 29>;
+			clocks = <&aux BCM2835_AUX_CLOCK_SPI2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pwm: pwm@7e20c000 {
+			compatible = "brcm,bcm2835-pwm";
+			reg = <0x7e20c000 0x28>;
+			clocks = <&clocks BCM2835_CLOCK_PWM>;
+			assigned-clocks = <&clocks BCM2835_CLOCK_PWM>;
+			assigned-clock-rates = <10000000>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		sdhci: mmc@7e300000 {
+			compatible = "brcm,bcm2835-sdhci";
+			reg = <0x7e300000 0x100>;
+			interrupts = <2 30>;
+			clocks = <&clocks BCM2835_CLOCK_EMMC>;
+			status = "disabled";
+		};
+
+		hvs@7e400000 {
+			compatible = "brcm,bcm2835-hvs";
+			reg = <0x7e400000 0x6000>;
+			interrupts = <2 1>;
+		};
+
+		dsi1: dsi@7e700000 {
+			compatible = "brcm,bcm2835-dsi1";
+			reg = <0x7e700000 0x8c>;
+			interrupts = <2 12>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+
+			clocks = <&clocks BCM2835_PLLD_DSI1>,
+				 <&clocks BCM2835_CLOCK_DSI1E>,
+				 <&clocks BCM2835_CLOCK_DSI1P>;
+			clock-names = "phy", "escape", "pixel";
+
+			clock-output-names = "dsi1_byte",
+					     "dsi1_ddr2",
+					     "dsi1_ddr";
+
+			status = "disabled";
+		};
+
+		i2c1: i2c@7e804000 {
+			compatible = "brcm,bcm2835-i2c";
+			reg = <0x7e804000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		usb: usb@7e980000 {
+			compatible = "brcm,bcm2835-usb";
+			reg = <0x7e980000 0x10000>;
+			interrupts = <1 9>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clk_usb>;
+			clock-names = "otg";
+			phys = <&usbphy>;
+			phy-names = "usb2-phy";
+		};
+	};
+
+	clocks {
+		/* The oscillator is the root of the clock tree. */
+		clk_osc: clk-osc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-output-names = "osc";
+			clock-frequency = <19200000>;
+		};
+
+		clk_usb: clk-usb {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-output-names = "otg";
+			clock-frequency = <480000000>;
+		};
+	};
+
+	usbphy: phy {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+};
diff --git a/src/arm/broadcom/bcm4708-asus-rt-ac56u.dts b/src/arm/broadcom/bcm4708-asus-rt-ac56u.dts
new file mode 100644
index 0000000..c80ac16
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-asus-rt-ac56u.dts
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Asus RT-AC56U
+ *
+ * Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "asus,rt-ac56u", "brcm,bcm4708";
+	model = "Asus RT-AC56U (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-usb3 {
+			label = "bcm53xx:blue:usb3";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wan {
+			label = "bcm53xx:blue:wan";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+		};
+
+		led-lan {
+			label = "bcm53xx:blue:lan";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power {
+			label = "bcm53xx:blue:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-all {
+			label = "bcm53xx:blue:all";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:blue:2ghz";
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb2 {
+			label = "bcm53xx:blue:usb2";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm4708-asus-rt-ac68u.dts b/src/arm/broadcom/bcm4708-asus-rt-ac68u.dts
new file mode 100644
index 0000000..3fe17bd
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-asus-rt-ac68u.dts
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Asus RT-AC68U
+ *
+ * Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "asus,rt-ac68u", "brcm,bcm4708";
+	model = "Asus RT-AC68U (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-usb2 {
+			label = "bcm53xx:blue:usb2";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power {
+			label = "bcm53xx:blue:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-logo {
+			label = "bcm53xx:white:logo";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-usb3 {
+			label = "bcm53xx:blue:usb3";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-brightness {
+			label = "Backlight";
+			linux,code = <KEY_BRIGHTNESS_ZERO>;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm4708-buffalo-wzr-1166dhp-common.dtsi b/src/arm/broadcom/bcm4708-buffalo-wzr-1166dhp-common.dtsi
new file mode 100644
index 0000000..9f90842
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-buffalo-wzr-1166dhp-common.dtsi
@@ -0,0 +1,193 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WZR-1166DHP and WZR-1166DHP2
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	spi {
+		compatible = "spi-gpio";
+		num-chipselects = <1>;
+		sck-gpios = <&chipcommon 7 0>;
+		mosi-gpios = <&chipcommon 4 0>;
+		cs-gpios = <&chipcommon 6 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hc595: gpio_spi@0 {
+			compatible = "fairchild,74hc595";
+			reg = <0>;
+			registers-number = <1>;
+			spi-max-frequency = <100000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-usb {
+			/* label = "bcm53xx:blue:usb"; */
+			function = LED_FUNCTION_USB;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>, <&ohci_port2>,
+					  <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-power0 {
+			/* label = "bcm53xx:red:power"; */
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-power1 {
+			/* label = "bcm53xx:white:power"; */
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-router0 {
+			/*  label = "bcm53xx:blue:router"; */
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-router1 {
+			/* label = "bcm53xx:amber:router"; */
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan {
+			/* label = "bcm53xx:blue:wan"; */
+			function = LED_FUNCTION_WAN;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wireless0 {
+			/* label = "bcm53xx:blue:wireless"; */
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wireless1 {
+			/* label = "bcm53xx:amber:wireless"; */
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-aoss {
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Commit mode set by switch? */
+		button-mode {
+			label = "Mode";
+			linux,code = <KEY_SETUP>;
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch: AP mode */
+		button-sw-ap {
+			label = "AP";
+			linux,code = <BTN_0>;
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+
+		button-eject {
+			label = "USB eject";
+			linux,code = <KEY_EJECTCD>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm4708-buffalo-wzr-1166dhp.dts b/src/arm/broadcom/bcm4708-buffalo-wzr-1166dhp.dts
new file mode 100644
index 0000000..8e50626
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-buffalo-wzr-1166dhp.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindigs for Buffalo WZR-1166DHP
+ *
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708-buffalo-wzr-1166dhp-common.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-1166dhp", "brcm,bcm4708";
+	model = "Buffalo WZR-1166DHP";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+};
diff --git a/src/arm/broadcom/bcm4708-buffalo-wzr-1166dhp2.dts b/src/arm/broadcom/bcm4708-buffalo-wzr-1166dhp2.dts
new file mode 100644
index 0000000..5961290
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-buffalo-wzr-1166dhp2.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindigs for Buffalo WZR-1166DHP2
+ *
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708-buffalo-wzr-1166dhp-common.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-1166dhp2", "brcm,bcm4708";
+	model = "Buffalo WZR-1166DHP2";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+};
diff --git a/src/arm/broadcom/bcm4708-buffalo-wzr-1750dhp.dts b/src/arm/broadcom/bcm4708-buffalo-wzr-1750dhp.dts
new file mode 100644
index 0000000..95ef6ca
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-buffalo-wzr-1750dhp.dts
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WZR-1750DHP
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-1750dhp", "brcm,bcm4708";
+	model = "Buffalo WZR-1750DHP (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		num-chipselects = <1>;
+		sck-gpios = <&chipcommon 7 0>;
+		mosi-gpios = <&chipcommon 4 0>;
+		cs-gpios = <&chipcommon 6 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hc595: gpio_spi@0 {
+			compatible = "fairchild,74hc595";
+			reg = <0>;
+			registers-number = <1>;
+			spi-max-frequency = <100000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-usb {
+			label = "bcm53xx:blue:usb";
+			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>, <&ohci_port2>,
+					  <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-power0 {
+			label = "bcm53xx:red:power";
+			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-power1 {
+			label = "bcm53xx:white:power";
+			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-router0 {
+			label = "bcm53xx:blue:router";
+			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-router1 {
+			label = "bcm53xx:amber:router";
+			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan {
+			label = "bcm53xx:blue:wan";
+			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wireless0 {
+			label = "bcm53xx:blue:wireless";
+			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wireless1 {
+			label = "bcm53xx:amber:wireless";
+			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-aoss {
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Commit mode set by switch? */
+		button-mode {
+			label = "Mode";
+			linux,code = <KEY_SETUP>;
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch: AP mode */
+		button-sw-ap {
+			label = "AP";
+			linux,code = <BTN_0>;
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+
+		button-eject {
+			label = "USB eject";
+			linux,code = <KEY_EJECTCD>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm4708-linksys-ea6300-v1.dts b/src/arm/broadcom/bcm4708-linksys-ea6300-v1.dts
new file mode 100644
index 0000000..0ed25bf
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-linksys-ea6300-v1.dts
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2017 Rafał Miłecki <rafal@milecki.pl>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "linksys,ea6300-v1", "brcm,bcm4708";
+	model = "Linksys EA6300 V1";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	nvram@1c080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1c080000 0x180000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm4708-linksys-ea6500-v2.dts b/src/arm/broadcom/bcm4708-linksys-ea6500-v2.dts
new file mode 100644
index 0000000..0454423
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-linksys-ea6500-v2.dts
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2017 Rafał Miłecki <rafal@milecki.pl>
+ * Copyright (C) 2018 Rene Kjellerup <rk.katana.steel@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "linksys,ea6500-v2", "brcm,bcm4708";
+	model = "Linksys EA6500 V2";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm4708-luxul-xap-1510.dts b/src/arm/broadcom/bcm4708-luxul-xap-1510.dts
new file mode 100644
index 0000000..72e960c
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-luxul-xap-1510.dts
@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+
+/ {
+	compatible = "luxul,xap-1510-v1", "brcm,bcm4708";
+	model = "Luxul XAP-1510 V1";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-5ghz {
+			label = "bcm53xx:blue:5ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:blue:2ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+		};
+
+		led-status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "poe";
+		};
+
+		port@4 {
+			label = "lan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm4708-luxul-xwc-1000.dts b/src/arm/broadcom/bcm4708-luxul-xwc-1000.dts
new file mode 100644
index 0000000..750e174
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-luxul-xwc-1000.dts
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Luxul XWC-1000
+ *
+ * Copyright 2014 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "luxul,xwc-1000", "brcm,bcm4708";
+	model = "Luxul XWC-1000 (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
+	nand_controller: nand-controller@18028000 {
+		nand@0 {
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "ubi";
+					reg = <0x00000000 0x08000000>;
+				};
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@4 {
+			label = "lan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm4708-netgear-r6250.dts b/src/arm/broadcom/bcm4708-netgear-r6250.dts
new file mode 100644
index 0000000..2bdbc7d
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-netgear-r6250.dts
@@ -0,0 +1,134 @@
+/*
+ * Broadcom BCM470X / BCM5301X arm platform code.
+ * DTS for Netgear R6250 V1
+ *
+ * Copyright 2013 Hauke Mehrtens <hauke@hauke-m.de>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "netgear,r6250-v1", "brcm,bcm4708";
+	model = "Netgear R6250 V1 (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-logo {
+			label = "bcm53xx:white:logo";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-power0 {
+			label = "bcm53xx:green:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-power1 {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb {
+			label = "bcm53xx:blue:usb";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-wireless {
+			label = "bcm53xx:blue:wireless";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+
+		button-rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm4708-netgear-r6300-v2.dts b/src/arm/broadcom/bcm4708-netgear-r6300-v2.dts
new file mode 100644
index 0000000..7739673
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-netgear-r6300-v2.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Netgear R6300 V2
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "netgear,r6300-v2", "brcm,bcm4708";
+	model = "Netgear R6300 V2 (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-logo {
+			label = "bcm53xx:white:logo";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-power0 {
+			label = "bcm53xx:green:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power1 {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-usb {
+			label = "bcm53xx:blue:usb";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wireless {
+			label = "bcm53xx:blue:wireless";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+
+		button-rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm4708-smartrg-sr400ac.dts b/src/arm/broadcom/bcm4708-smartrg-sr400ac.dts
new file mode 100644
index 0000000..b226bef
--- /dev/null
+++ b/src/arm/broadcom/bcm4708-smartrg-sr400ac.dts
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X arm platform code.
+ * DTS for SmartRG SR400ac
+ *
+ * Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "smartrg,sr400ac", "brcm,bcm4708";
+	model = "SmartRG SR400ac";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power-white {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-power-amber {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-usb2 {
+			label = "bcm53xx:white:usb2";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port2>, <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-usb3-white {
+			label = "bcm53xx:white:usb3";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-usb3-green {
+			label = "bcm53xx:green:usb3";
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-wps {
+			label = "bcm53xx:white:wps";
+			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-status-red {
+			label = "bcm53xx:red:status";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-status-green {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-status-blue {
+			label = "bcm53xx:blue:status";
+			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan-white {
+			label = "bcm53xx:white:wan";
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan-red {
+			label = "bcm53xx:red:wan";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm4708.dtsi b/src/arm/broadcom/bcm4708.dtsi
new file mode 100644
index 0000000..1a19e97
--- /dev/null
+++ b/src/arm/broadcom/bcm4708.dtsi
@@ -0,0 +1,48 @@
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for BCM4708 SoC.
+ *
+ * Copyright 2013-2014 Hauke Mehrtens <hauke@hauke-m.de>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include "bcm5301x.dtsi"
+
+/ {
+	compatible = "brcm,bcm4708";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "brcm,bcm-nsp-smp";
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			reg = <0x0>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			secondary-boot-reg = <0xffff0400>;
+			reg = <0x1>;
+		};
+	};
+
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm47081-asus-rt-n18u.dts b/src/arm/broadcom/bcm47081-asus-rt-n18u.dts
new file mode 100644
index 0000000..3854db0
--- /dev/null
+++ b/src/arm/broadcom/bcm47081-asus-rt-n18u.dts
@@ -0,0 +1,79 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Asus RT-N18U
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm47081.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "asus,rt-n18u", "brcm,bcm47081", "brcm,bcm4708";
+	model = "Asus RT-N18U (BCM47081)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			label = "bcm53xx:blue:power";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-usb2 {
+			label = "bcm53xx:blue:usb2";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wan {
+			label = "bcm53xx:blue:wan";
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-lan {
+			label = "bcm53xx:blue:lan";
+			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-usb3 {
+			label = "bcm53xx:blue:usb3";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm47081-buffalo-wzr-600dhp2.dts b/src/arm/broadcom/bcm47081-buffalo-wzr-600dhp2.dts
new file mode 100644
index 0000000..192b8db
--- /dev/null
+++ b/src/arm/broadcom/bcm47081-buffalo-wzr-600dhp2.dts
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WZR-600DHP2
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm47081.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-600dhp2", "brcm,bcm47081", "brcm,bcm4708";
+	model = "Buffalo WZR-600DHP2 (BCM47081)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		num-chipselects = <1>;
+		sck-gpios = <&chipcommon 7 0>;
+		mosi-gpios = <&chipcommon 4 0>;
+		cs-gpios = <&chipcommon 6 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hc595: gpio_spi@0 {
+			compatible = "fairchild,74hc595";
+			reg = <0>;
+			registers-number = <1>;
+			spi-max-frequency = <100000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power0 {
+			label = "bcm53xx:green:power";
+			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-power1 {
+			label = "bcm53xx:red:power";
+			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-router0 {
+			label = "bcm53xx:green:router";
+			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-router1 {
+			label = "bcm53xx:amber:router";
+			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan {
+			label = "bcm53xx:green:wan";
+			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wireless0 {
+			label = "bcm53xx:green:wireless";
+			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wireless1 {
+			label = "bcm53xx:amber:wireless";
+			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-aoss {
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch device mode? */
+		button-mode {
+			label = "Mode";
+			linux,code = <KEY_SETUP>;
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+
+		button-eject {
+			label = "USB eject";
+			linux,code = <KEY_EJECTCD>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47081-buffalo-wzr-900dhp.dts b/src/arm/broadcom/bcm47081-buffalo-wzr-900dhp.dts
new file mode 100644
index 0000000..7655e4f
--- /dev/null
+++ b/src/arm/broadcom/bcm47081-buffalo-wzr-900dhp.dts
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WZR-900DHP
+ *
+ * Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm47081.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-900dhp", "brcm,bcm47081", "brcm,bcm4708";
+	model = "Buffalo WZR-900DHP (BCM47081)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		num-chipselects = <1>;
+		sck-gpios = <&chipcommon 7 0>;
+		mosi-gpios = <&chipcommon 4 0>;
+		cs-gpios = <&chipcommon 6 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hc595: gpio_spi@0 {
+			compatible = "fairchild,74hc595";
+			reg = <0>;
+			registers-number = <1>;
+			spi-max-frequency = <100000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-usb {
+			label = "bcm53xx:green:usb";
+			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-power0 {
+			label = "bcm53xx:green:power";
+			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-power1 {
+			label = "bcm53xx:red:power";
+			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-router0 {
+			label = "bcm53xx:green:router";
+			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-router1 {
+			label = "bcm53xx:amber:router";
+			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan {
+			label = "bcm53xx:green:wan";
+			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wireless0 {
+			label = "bcm53xx:green:wireless";
+			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wireless1 {
+			label = "bcm53xx:amber:wireless";
+			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm47081-luxul-xap-1410.dts b/src/arm/broadcom/bcm47081-luxul-xap-1410.dts
new file mode 100644
index 0000000..0198b5f
--- /dev/null
+++ b/src/arm/broadcom/bcm47081-luxul-xap-1410.dts
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm47081.dtsi"
+
+/ {
+	compatible = "luxul,xap-1410-v1", "brcm,bcm47081", "brcm,bcm4708";
+	model = "Luxul XAP-1410 V1";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-5ghz {
+			label = "bcm53xx:blue:5ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:blue:2ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+		};
+
+		led-status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@4 {
+			label = "poe";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47081-luxul-xwr-1200.dts b/src/arm/broadcom/bcm47081-luxul-xwr-1200.dts
new file mode 100644
index 0000000..73ff169
--- /dev/null
+++ b/src/arm/broadcom/bcm47081-luxul-xwr-1200.dts
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm47081.dtsi"
+#include "bcm5301x-nand-cs0-bch4.dtsi"
+
+/ {
+	compatible = "luxul,xwr-1200-v1", "brcm,bcm47081", "brcm,bcm4708";
+	model = "Luxul XWR-1200 V1";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			label = "bcm53xx:green:power";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-lan3 {
+			label = "bcm53xx:green:lan3";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+		};
+
+		led-lan4 {
+			label = "bcm53xx:green:lan4";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+		};
+
+		led-wan {
+			label = "bcm53xx:green:wan";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+		};
+
+		led-lan2 {
+			label = "bcm53xx:green:lan2";
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+		};
+
+		led-usb {
+			label = "bcm53xx:green:usb";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port2>, <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:green:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+		};
+
+		led-5ghz {
+			label = "bcm53xx:green:5ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+		};
+
+		led-lan1 {
+			label = "bcm53xx:green:lan1";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+			nvmem-cells = <&et0macaddr 5>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47081-tplink-archer-c5-v2.dts b/src/arm/broadcom/bcm47081-tplink-archer-c5-v2.dts
new file mode 100644
index 0000000..b6a5886
--- /dev/null
+++ b/src/arm/broadcom/bcm47081-tplink-archer-c5-v2.dts
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2017 Rafał Miłecki <rafal@milecki.pl>
+ */
+
+/dts-v1/;
+
+#include "bcm47081.dtsi"
+
+/ {
+	compatible = "tplink,archer-c5-v2", "brcm,bcm47081", "brcm,bcm4708";
+	model = "TP-LINK Archer C5 V2";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-2ghz {
+			label = "bcm53xx:green:2ghz";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-lan {
+			label = "bcm53xx:green:lan";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-usb2-port1 {
+			label = "bcm53xx:green:usb2-port1";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-power {
+			label = "bcm53xx:green:power";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wan-green {
+			label = "bcm53xx:green:wan";
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wps {
+			label = "bcm53xx:green:wps";
+			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan-amber {
+			label = "bcm53xx:amber:wan";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:green:5ghz";
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-usb2-port2 {
+			label = "bcm53xx:green:usb2-port2";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port2>, <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&spi_nor {
+	status = "okay";
+
+	partitions {
+		compatible = "tplink,safeloader-partitions";
+		partitions-table-offset = <0xe50000>;
+
+		partition-os-image {
+			compatible = "brcm,trx";
+		};
+
+		partition-file-system {
+			linux,rootfs;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
diff --git a/src/arm/broadcom/bcm47081.dtsi b/src/arm/broadcom/bcm47081.dtsi
new file mode 100644
index 0000000..ed13af0
--- /dev/null
+++ b/src/arm/broadcom/bcm47081.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for BCM47081 SoC.
+ *
+ * Copyright © 2014 Rafał Miłecki <zajec5@gmail.com>
+ */
+
+#include "bcm5301x.dtsi"
+
+/ {
+	compatible = "brcm,bcm47081";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			reg = <0x0>;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm4709-asus-rt-ac87u.dts b/src/arm/broadcom/bcm4709-asus-rt-ac87u.dts
new file mode 100644
index 0000000..5940021
--- /dev/null
+++ b/src/arm/broadcom/bcm4709-asus-rt-ac87u.dts
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Asus RT-AC87U
+ *
+ * Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4709.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "asus,rt-ac87u", "brcm,bcm4709", "brcm,bcm4708";
+	model = "Asus RT-AC87U";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	nvram@1c080000 {
+		et1macaddr: et1macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-wps {
+			label = "bcm53xx:blue:wps";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power {
+			label = "bcm53xx:blue:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wan {
+			label = "bcm53xx:red:wan";
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et1macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&nandcs {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		boot@0 {
+			label = "boot";
+			reg = <0x00000000 0x00080000>;
+			read-only;
+		};
+
+		nvram@80000 {
+			label = "nvram";
+			reg = <0x00080000 0x00180000>;
+		};
+
+		firmware@200000 {
+			label = "firmware";
+			reg = <0x00200000 0x07cc0000>;
+			compatible = "brcm,trx";
+		};
+
+		asus@7ec0000 {
+			label = "asus";
+			reg = <0x07ec0000 0x00140000>;
+			read-only;
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm4709-buffalo-wxr-1900dhp.dts b/src/arm/broadcom/bcm4709-buffalo-wxr-1900dhp.dts
new file mode 100644
index 0000000..b7cd2fa
--- /dev/null
+++ b/src/arm/broadcom/bcm4709-buffalo-wxr-1900dhp.dts
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WXR-1900DHP
+ *
+ * Copyright (C) 2015 Felix Fietkau <nbd@openwrt.org>
+ */
+
+/dts-v1/;
+
+#include "bcm4709.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "buffalo,wxr-1900dhp", "brcm,bcm4709", "brcm,bcm4708";
+	model = "Buffalo WXR-1900DHP";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-usb {
+			label = "bcm53xx:green:usb";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-power-amber {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-power-white {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-router-amber {
+			label = "bcm53xx:amber:router";
+			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-router-white {
+			label = "bcm53xx:white:router";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan-amber {
+			label = "bcm53xx:amber:wan";
+			gpios = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan-white {
+			label = "bcm53xx:white:wan";
+			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wireless-amber {
+			label = "bcm53xx:amber:wireless";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wireless-white {
+			label = "bcm53xx:white:wireless";
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-power {
+			label = "Power";
+			linux,code = <KEY_POWER>;
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+
+		button-aoss {
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Commit mode set by switch? */
+		button-mode {
+			label = "Mode";
+			linux,code = <KEY_SETUP>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch: AP mode */
+		button-sw-ap {
+			label = "AP";
+			linux,code = <BTN_0>;
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+		};
+
+		button-eject {
+			label = "USB eject";
+			linux,code = <KEY_EJECTCD>;
+			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+
+&usb2 {
+	vcc-gpio = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm4709-linksys-ea9200.dts b/src/arm/broadcom/bcm4709-linksys-ea9200.dts
new file mode 100644
index 0000000..2ba5adf
--- /dev/null
+++ b/src/arm/broadcom/bcm4709-linksys-ea9200.dts
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2017 Rafał Miłecki <rafal@milecki.pl>
+ */
+
+/dts-v1/;
+
+#include "bcm4709.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "linksys,ea9200", "brcm,bcm4709", "brcm,bcm4708";
+	model = "Linksys EA9200";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	nvram@1c080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1c080000 0x180000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			status = "disabled";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm4709-netgear-r7000.dts b/src/arm/broadcom/bcm4709-netgear-r7000.dts
new file mode 100644
index 0000000..24ba8f8
--- /dev/null
+++ b/src/arm/broadcom/bcm4709-netgear-r7000.dts
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Netgear R7000
+ *
+ * Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4709.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "netgear,r7000", "brcm,bcm4709", "brcm,bcm4708";
+	model = "Netgear R7000";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power-white {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-power-amber {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:white:5ghz";
+			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2ghz {
+			label = "bcm53xx:white:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wps {
+			label = "bcm53xx:white:wps";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wireless {
+			label = "bcm53xx:white:wireless";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-usb3 {
+			label = "bcm53xx:white:usb3";
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb2 {
+			label = "bcm53xx:white:usb2";
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+
+		button-rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm4709-netgear-r8000.dts b/src/arm/broadcom/bcm4709-netgear-r8000.dts
new file mode 100644
index 0000000..127ca87
--- /dev/null
+++ b/src/arm/broadcom/bcm4709-netgear-r8000.dts
@@ -0,0 +1,252 @@
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Netgear R8000
+ *
+ * Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
+ * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
+ * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
+ * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
+ * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
+ * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
+ * PERFORMANCE OF THIS SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "bcm4709.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "netgear,r8000", "brcm,bcm4709", "brcm,bcm4708";
+	model = "Netgear R8000 (BCM4709)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power-white {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-power-amber {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wan-white {
+			label = "bcm53xx:white:wan";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wan-amber {
+			label = "bcm53xx:amber:wan";
+			gpios = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5ghz-1 {
+			label = "bcm53xx:white:5ghz-1";
+			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2ghz {
+			label = "bcm53xx:white:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wireless {
+			label = "bcm53xx:white:wireless";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wps {
+			label = "bcm53xx:white:wps";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5ghz-2 {
+			label = "bcm53xx:white:5ghz-2";
+			gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb3 {
+			label = "bcm53xx:white:usb3";
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb2 {
+			label = "bcm53xx:white:usb2";
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+		};
+
+		button-brightness {
+			label = "Backlight";
+			linux,code = <KEY_BRIGHTNESS_ZERO>;
+			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&pcie0 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,1,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			ieee80211-freq-limit = <5735000 5835000>;
+			brcm,ccode-map = "JP-JP-78", "US-Q2-86";
+		};
+	};
+};
+
+&pcie1 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@1,0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		bridge@1,1,0 {
+			reg = <0x0000 0 0 0 0>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			bridge@1,0 {
+				reg = <0x800 0 0 0 0>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+
+				wifi@0,0 {
+					compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+					reg = <0x0000 0 0 0 0>;
+					brcm,ccode-map = "JP-JP-78", "US-Q2-86";
+				};
+			};
+
+			bridge@1,2,2 {
+				reg = <0x1000 0 0 0 0>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+
+				wifi@1,4,0 {
+					compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+					reg = <0x0000 0 0 0 0>;
+					ieee80211-freq-limit = <5170000 5730000>;
+					brcm,ccode-map = "JP-JP-78", "US-Q2-86";
+				};
+			};
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			status = "disabled";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@7 {
+			status = "disabled";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm4709-tplink-archer-c9-v1.dts b/src/arm/broadcom/bcm4709-tplink-archer-c9-v1.dts
new file mode 100644
index 0000000..5a8b2b1
--- /dev/null
+++ b/src/arm/broadcom/bcm4709-tplink-archer-c9-v1.dts
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2016 Rafał Miłecki <rafal@milecki.pl>
+ */
+
+/dts-v1/;
+
+#include "bcm4709.dtsi"
+
+/ {
+	compatible = "tplink,archer-c9-v1", "brcm,bcm4709", "brcm,bcm4708";
+	model = "TP-LINK Archer C9 V1";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-lan {
+			label = "bcm53xx:blue:lan";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wps {
+			label = "bcm53xx:blue:wps";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2ghz {
+			label = "bcm53xx:blue:2ghz";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:blue:5ghz";
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-usb3 {
+			label = "bcm53xx:blue:usb3";
+			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-usb2 {
+			label = "bcm53xx:blue:usb2";
+			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port2>, <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-wan-blue {
+			label = "bcm53xx:blue:wan";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan-amber {
+			label = "bcm53xx:amber:wan";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-power {
+			label = "bcm53xx:blue:power";
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+};
+
+&spi_nor {
+	status = "okay";
+
+	partitions {
+		compatible = "tplink,safeloader-partitions";
+		partitions-table-offset = <0xe50000>;
+
+		partition-os-image {
+			compatible = "brcm,trx";
+		};
+
+		partition-file-system {
+			linux,rootfs;
+		};
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm4709.dtsi b/src/arm/broadcom/bcm4709.dtsi
new file mode 100644
index 0000000..cba3d91
--- /dev/null
+++ b/src/arm/broadcom/bcm4709.dtsi
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2016 Rafał Miłecki <rafal@milecki.pl>
+ */
+
+#include "bcm4708.dtsi"
+
+&uart0 {
+	clock-frequency = <125000000>;
+	status = "okay";
+};
+
+&srab {
+	compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab";
+};
diff --git a/src/arm/broadcom/bcm47094-asus-rt-ac3100.dts b/src/arm/broadcom/bcm47094-asus-rt-ac3100.dts
new file mode 100644
index 0000000..5f08930
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-asus-rt-ac3100.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Arınç ÜNAL <arinc.unal@arinc9.com>
+ */
+
+/dts-v1/;
+
+#include "bcm47094-asus-rt-ac3100.dtsi"
+
+/ {
+	compatible = "asus,rt-ac3100", "brcm,bcm47094", "brcm,bcm4708";
+	model = "ASUS RT-AC3100";
+
+	nvram@1c080000 {
+		et0macaddr: et0macaddr {
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
diff --git a/src/arm/broadcom/bcm47094-asus-rt-ac3100.dtsi b/src/arm/broadcom/bcm47094-asus-rt-ac3100.dtsi
new file mode 100644
index 0000000..09cefce
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-asus-rt-ac3100.dtsi
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Arınç ÜNAL <arinc.unal@arinc9.com>
+ */
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	nvram@1c080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1c080000 0x00180000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			label = "white:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wan-red {
+			label = "red:wan";
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-lan {
+			label = "white:lan";
+			gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb2 {
+			label = "white:usb2";
+			gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-usb3 {
+			label = "white:usb3";
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ehci_port1>, <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-wps {
+			label = "white:wps";
+			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
+		};
+
+		button-reset {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wifi {
+			label = "Wi-Fi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+		};
+
+		button-led {
+			label = "Backlight";
+			linux,code = <KEY_BRIGHTNESS_ZERO>;
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&srab {
+	compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab";
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			label = "cpu";
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&nandcs {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x00080000>;
+			read-only;
+		};
+
+		partition@80000 {
+			label = "nvram";
+			reg = <0x00080000 0x00180000>;
+		};
+
+		partition@200000 {
+			label = "firmware";
+			reg = <0x00200000 0x07e00000>;
+			compatible = "brcm,trx";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47094-asus-rt-ac88u.dts b/src/arm/broadcom/bcm47094-asus-rt-ac88u.dts
new file mode 100644
index 0000000..fd344b5
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-asus-rt-ac88u.dts
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Arınç ÜNAL <arinc.unal@arinc9.com>
+ */
+
+/dts-v1/;
+
+#include "bcm47094-asus-rt-ac3100.dtsi"
+
+/ {
+	compatible = "asus,rt-ac88u", "brcm,bcm47094", "brcm,bcm4708";
+	model = "ASUS RT-AC88U";
+
+	nvram@1c080000 {
+		et1macaddr: et1macaddr {
+		};
+	};
+
+	switch {
+		compatible = "realtek,rtl8365mb";
+		/* 7 = MDIO (has input reads), 6 = MDC (clock, output only) */
+		mdc-gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
+		mdio-gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+		realtek,disable-leds;
+		dsa,member = <1 0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "lan5";
+				phy-handle = <&ethphy0>;
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan6";
+				phy-handle = <&ethphy1>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan7";
+				phy-handle = <&ethphy2>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan8";
+				phy-handle = <&ethphy3>;
+			};
+
+			port@6 {
+				reg = <6>;
+				label = "cpu";
+				ethernet = <&sw0_p5>;
+				phy-mode = "rgmii";
+				tx-internal-delay-ps = <2000>;
+				rx-internal-delay-ps = <2100>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+					pause;
+				};
+			};
+		};
+
+		mdio {
+			compatible = "realtek,smi-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethphy0: ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			ethphy1: ethernet-phy@1 {
+				reg = <1>;
+			};
+
+			ethphy2: ethernet-phy@2 {
+				reg = <2>;
+			};
+
+			ethphy3: ethernet-phy@3 {
+				reg = <3>;
+			};
+		};
+	};
+};
+
+&srab {
+	dsa,member = <0 0>;
+
+	ports {
+		sw0_p5: port@5 {
+			/delete-property/ethernet;
+
+			label = "extsw";
+			phy-mode = "rgmii";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&gmac0 {
+	status = "disabled";
+};
+
+&gmac1 {
+	nvmem-cells = <&et1macaddr>;
+	nvmem-cell-names = "mac-address";
+};
diff --git a/src/arm/broadcom/bcm47094-dlink-dir-885l.dts b/src/arm/broadcom/bcm47094-dlink-dir-885l.dts
new file mode 100644
index 0000000..c5099de
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-dlink-dir-885l.dts
@@ -0,0 +1,175 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for D-Link DIR-885L
+ *
+ * Copyright (C) 2016 Rafał Miłecki <zajec5@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch1.dtsi"
+
+/ {
+	compatible = "dlink,dir-885l", "brcm,bcm47094", "brcm,bcm4708";
+	model = "D-Link DIR-885L";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	nvram@1e3f0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1e3f0000 0x10000>;
+
+		et2macaddr: et2macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
+	nand_controller: nand-controller@18028000 {
+		nand@0 {
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					compatible = "seama";
+					label = "firmware";
+					reg = <0x00000000 0x08000000>;
+				};
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power-white {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wan-white {
+			label = "bcm53xx:white:wan";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power-amber {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wan-amber {
+			label = "bcm53xx:amber:wan";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb3-white {
+			label = "bcm53xx:white:usb3";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:white:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:white:5ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch: router / extender */
+		button-extender {
+			label = "Extender";
+			linux,code = <BTN_0>;
+			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+};
+
+&gmac0 {
+	nvmem-cells = <&et2macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+			nvmem-cells = <&et2macaddr 3>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@5 {
+			status = "disabled";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47094-dlink-dir-890l.dts b/src/arm/broadcom/bcm47094-dlink-dir-890l.dts
new file mode 100644
index 0000000..3124dfd
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-dlink-dir-890l.dts
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device tree for D-Link DIR-890L
+ * D-Link calls this board "WRGAC36"
+ * this router has the same looks and form factor as D-Link DIR-885L.
+ *
+ * Some differences from DIR-885L include a separate USB2 port, separate LEDs
+ * for USB2 and USB3, a separate VCC supply for the USB2 slot and no
+ * router/extender switch is mounted (there is an empty mount point on the
+ * PCB) so this device is a pure router. Also the LAN ports are in the right
+ * order.
+ *
+ * Based on the device tree for DIR-885L
+ * Copyright (C) 2016 Rafał Miłecki <zajec5@gmail.com>
+ * Copyright (C) 2022 Linus Walleij
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch1.dtsi"
+
+/ {
+	compatible = "dlink,dir-890l", "brcm,bcm47094", "brcm,bcm4708";
+	model = "D-Link DIR-890L";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		/*
+		 * LED information is derived from the boot log which
+		 * conveniently lists all the LEDs.
+		 */
+		compatible = "gpio-leds";
+
+		led-power-white {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wan-white {
+			label = "bcm53xx:white:wan";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power-amber {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wan-amber {
+			label = "bcm53xx:amber:wan";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb3-white {
+			label = "bcm53xx:white:usb3";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-usb2-white {
+			label = "bcm53xx:white:usb2";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:white:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:white:5ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Called "factory reset" in the vendor dmesg */
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/*
+	 * The flash memory is memory mapped at 0x1e000000-0x1fffffff
+	 * 64KB blocks; total size 2MB, same that can be
+	 * found attached to the spi_nor SPI controller.
+	 */
+	nvram@1e1f0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1e1f0000 0x00010000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+};
+
+&gmac2 {
+	/*
+	 * The NVRAM curiously does not contain a MAC address
+	 * for et2 so since that is the only ethernet interface
+	 * actually in use on the platform, we use this et0 MAC
+	 * address for et2.
+	 */
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&nandcs {
+	/* Spansion S34ML01G2, 128MB with 128KB erase blocks */
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/*
+		 * This is called "nflash" in the vendor kernel with
+		 * "upgrade" and "rootfs" (probably using OpenWrt
+		 * splitpart). We call it "firmware" like standard tools
+		 * assume. The CFE loader contains incorrect information
+		 * about TRX partitions, ignore this, there are no TRX
+		 * partitions: this device uses SEAMA.
+		 */
+		firmware@0 {
+			compatible = "seama";
+			label = "firmware";
+			reg = <0x00000000 0x08000000>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpios = <&chipcommon 21 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpios = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			status = "disabled";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			label = "cpu";
+			phy-mode = "rgmii";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47094-linksys-panamera.dts b/src/arm/broadcom/bcm47094-linksys-panamera.dts
new file mode 100644
index 0000000..2b5c80d
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-linksys-panamera.dts
@@ -0,0 +1,302 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2017 Rafał Miłecki <rafal@milecki.pl>
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "linksys,panamera", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Linksys EA9500";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	nvram@1c080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1c080000 0x100000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		button-rfkill {
+				label = "WiFi";
+				linux,code = <KEY_RFKILL>;
+				gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
+		};
+
+		button-reset {
+				label = "Reset";
+				linux,code = <KEY_RESTART>;
+				gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-wps {
+			label = "bcm53xx:white:wps";
+			gpios = <&chipcommon 22 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb2 {
+			label = "bcm53xx:green:usb2";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port2>, <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-usb3 {
+			label = "bcm53xx:green:usb3";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-power {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wifi-disabled {
+			label = "bcm53xx:amber:wifi-disabled";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wifi-enabled {
+			label = "bcm53xx:white:wifi-enabled";
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-bluebar1 {
+			label = "bcm53xx:white:bluebar1";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-bluebar2 {
+			label = "bcm53xx:white:bluebar2";
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-bluebar3 {
+			label = "bcm53xx:white:bluebar3";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+
+		led-bluebar4 {
+			label = "bcm53xx:white:bluebar4";
+			gpios = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-bluebar5 {
+			label = "bcm53xx:white:bluebar5";
+			gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-bluebar6 {
+			label = "bcm53xx:white:bluebar6";
+			gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-bluebar7 {
+			label = "bcm53xx:white:bluebar7";
+			gpios = <&chipcommon 21 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-bluebar8 {
+			label = "bcm53xx:white:bluebar8";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	mdio-mux@18003000 {
+
+		/* BIT(9) = 1 => external mdio */
+		mdio@200 {
+			reg = <0x200>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch@0  {
+				compatible = "brcm,bcm53125";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+				reset-names = "robo_reset";
+				reg = <0>;
+				dsa,member = <1 0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinmux_mdio>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						label = "lan1";
+					};
+
+					port@1 {
+						reg = <1>;
+						label = "lan5";
+					};
+
+					port@2 {
+						reg = <2>;
+						label = "lan2";
+					};
+
+					port@3 {
+						reg = <3>;
+						label = "lan6";
+					};
+
+					port@4 {
+						reg = <4>;
+						label = "lan3";
+					};
+
+					sw1_p8: port@8 {
+						reg = <8>;
+						ethernet = <&sw0_p0>;
+						label = "cpu";
+
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+				};
+			};
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
+};
+
+&srab {
+	compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab";
+	status = "okay";
+	dsa,member = <0 0>;
+
+	ports {
+		sw0_p0: port@0 {
+			label = "extsw";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@1 {
+			label = "lan7";
+		};
+
+		port@2 {
+			label = "lan4";
+		};
+
+		port@3 {
+			label = "lan8";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			label = "cpu";
+			status = "disabled";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@7 {
+			label = "cpu";
+			status = "disabled";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&nandcs {
+	partitions {
+		compatible = "linksys,ns-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x0000000 0x0080000>;
+			read-only;
+		};
+
+		partition@80000 {
+			label = "nvram";
+			reg = <0x080000 0x0100000>;
+		};
+
+		partition@180000 {
+			label = "devinfo";
+			reg = <0x0180000 0x080000>;
+		};
+
+		partition@200000 {
+			reg = <0x0200000 0x01d00000>;
+			compatible = "linksys,ns-firmware", "brcm,trx";
+		};
+
+		partition@1f00000 {
+			reg = <0x01f00000 0x01d00000>;
+			compatible = "linksys,ns-firmware", "brcm,trx";
+		};
+
+		partition@5200000 {
+			label = "system";
+			reg = <0x05200000 0x02e00000>;
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47094-luxul-abr-4500.dts b/src/arm/broadcom/bcm47094-luxul-abr-4500.dts
new file mode 100644
index 0000000..e374062
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-luxul-abr-4500.dts
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2017 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "luxul,abr-4500-v1", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Luxul ABR-4500 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		led-usb3 {
+			label = "bcm53xx:green:usb3";
+			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+				<&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "wan";
+			nvmem-cells = <&et0macaddr 1>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@1 {
+			label = "lan4";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan2";
+		};
+
+		port@4 {
+			label = "lan1";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47094-luxul-xap-1610.dts b/src/arm/broadcom/bcm47094-luxul-xap-1610.dts
new file mode 100644
index 0000000..badafa0
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-luxul-xap-1610.dts
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+
+/ {
+	compatible = "luxul,xap-1610-v1", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Luxul XAP-1610 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:blue:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:blue:5ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+
+&pcie0 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			brcm,ccode-map = "AU-AU-920", "CA-CA-892", "GB-DE-964", "NZ-AU-920", "US-US-825";
+		};
+	};
+};
+
+&pcie1 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			brcm,ccode-map = "AU-AU-920", "CA-CA-892", "GB-DE-964", "NZ-AU-920", "US-US-825";
+		};
+	};
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "poe";
+		};
+
+		port@1 {
+			label = "lan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47094-luxul-xbr-4500.dts b/src/arm/broadcom/bcm47094-luxul-xbr-4500.dts
new file mode 100644
index 0000000..cf95af9
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-luxul-xbr-4500.dts
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2017 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "luxul,xbr-4500-v1", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Luxul XBR-4500 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "timer";
+		};
+
+		led-usb3 {
+			label = "bcm53xx:green:usb3";
+			gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+				<&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "wan";
+			nvmem-cells = <&et0macaddr 1>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@1 {
+			label = "lan4";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan2";
+		};
+
+		port@4 {
+			label = "lan1";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47094-luxul-xwc-2000.dts b/src/arm/broadcom/bcm47094-luxul-xwc-2000.dts
new file mode 100644
index 0000000..992c19e
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-luxul-xwc-2000.dts
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2019 Legrand AV Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "luxul,xwc-2000-v1", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Luxul XWC-2000 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47094-luxul-xwr-3100.dts b/src/arm/broadcom/bcm47094-luxul-xwr-3100.dts
new file mode 100644
index 0000000..4d0ba31
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-luxul-xwr-3100.dts
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch4.dtsi"
+
+/ {
+	compatible = "luxul,xwr-3100-v1", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Luxul XWR-3100 V1";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			label = "bcm53xx:green:power";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-lan3 {
+			label = "bcm53xx:green:lan3";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+		};
+
+		led-lan4 {
+			label = "bcm53xx:green:lan4";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wan {
+			label = "bcm53xx:green:wan";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led-lan1 {
+			label = "bcm53xx:green:lan1";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+
+		led-lan2 {
+			label = "bcm53xx:green:lan2";
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb3 {
+			label = "bcm53xx:green:usb3";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:green:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:green:5ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+			nvmem-cells = <&et0macaddr 5>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47094-luxul-xwr-3150-v1.dts b/src/arm/broadcom/bcm47094-luxul-xwr-3150-v1.dts
new file mode 100644
index 0000000..83c429a
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-luxul-xwr-3150-v1.dts
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "luxul,xwr-3150-v1", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Luxul XWR-3150 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			label = "bcm53xx:green:power";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-usb3 {
+			label = "bcm53xx:green:usb3";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:green:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:green:5ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&pcie0 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			brcm,ccode-map = "AU-AU-953", "CA-CA-946", "GB-E0-846", "NZ-AU-953", "US-Q2-930";
+		};
+	};
+};
+
+&pcie1 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			brcm,ccode-map = "AU-AU-953", "CA-CA-946", "GB-E0-846", "NZ-AU-953", "US-Q2-930";
+		};
+	};
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+			nvmem-cells = <&et0macaddr 5>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47094-netgear-r8500.dts b/src/arm/broadcom/bcm47094-netgear-r8500.dts
new file mode 100644
index 0000000..76d5626
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-netgear-r8500.dts
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2016 Rafał Miłecki <rafal@milecki.pl>
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "netgear,r8500", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Netgear R8500";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power0 {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-power1 {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz-1 {
+			label = "bcm53xx:white:5ghz-1";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz-2 {
+			label = "bcm53xx:white:5ghz-2";
+			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2ghz {
+			label = "bcm53xx:white:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb2 {
+			label = "bcm53xx:white:usb2";
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb3 {
+			label = "bcm53xx:white:usb3";
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-brightness {
+			label = "Backlight";
+			linux,code = <KEY_BRIGHTNESS_ZERO>;
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+
+		button-rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm47094-phicomm-k3.dts b/src/arm/broadcom/bcm47094-phicomm-k3.dts
new file mode 100644
index 0000000..bb1bc4e
--- /dev/null
+++ b/src/arm/broadcom/bcm47094-phicomm-k3.dts
@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2017 Hamster Tian <haotia@gmail.com>
+ * Copyright (C) 2019 Hao Dong <halbertdong@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch4.dtsi"
+
+/ {
+	compatible = "phicomm,k3", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Phicomm K3";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&nandcs {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x0000000 0x0080000>;
+			read-only;
+		};
+
+		partition@80000 {
+			label = "nvram";
+			reg = <0x0080000 0x0100000>;
+		};
+
+		partition@180000 {
+			label = "phicomm";
+			reg = <0x0180000 0x0280000>;
+			read-only;
+		};
+
+		partition@400000 {
+			label = "firmware";
+			reg = <0x0400000 0x7C00000>;
+			compatible = "brcm,trx";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47094.dtsi b/src/arm/broadcom/bcm47094.dtsi
new file mode 100644
index 0000000..6282363
--- /dev/null
+++ b/src/arm/broadcom/bcm47094.dtsi
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2016 Rafał Miłecki <rafal@milecki.pl>
+ */
+
+#include "bcm4708.dtsi"
+
+/ {
+};
+
+&pinctrl {
+	compatible = "brcm,bcm4709-pinmux";
+
+	pinmux_mdio: mdio-pins {
+		groups = "mdio_grp";
+		function = "mdio";
+	};
+};
+
+&usb3_phy {
+	compatible = "brcm,ns-bx-usb3-phy";
+};
+
+&uart0 {
+	clock-frequency = <125000000>;
+	status = "okay";
+};
+
+&srab {
+	compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab";
+};
diff --git a/src/arm/broadcom/bcm47189-luxul-xap-1440.dts b/src/arm/broadcom/bcm47189-luxul-xap-1440.dts
new file mode 100644
index 0000000..ac44c74
--- /dev/null
+++ b/src/arm/broadcom/bcm47189-luxul-xap-1440.dts
@@ -0,0 +1,66 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm53573.dtsi"
+
+/ {
+	compatible = "luxul,xap-1440-v1", "brcm,bcm47189", "brcm,bcm53573";
+	model = "Luxul XAP-1440 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-wlan {
+			label = "bcm53xx:blue:wlan";
+			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led-system {
+			label = "bcm53xx:green:system";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-handle = <&bcm54210e>;
+
+	/delete-node/ fixed-link;
+
+	mdio {
+		/delete-node/ switch@1e;
+
+		bcm54210e: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gmac1 {
+	status = "disabled";
+};
diff --git a/src/arm/broadcom/bcm47189-luxul-xap-810.dts b/src/arm/broadcom/bcm47189-luxul-xap-810.dts
new file mode 100644
index 0000000..fd071da
--- /dev/null
+++ b/src/arm/broadcom/bcm47189-luxul-xap-810.dts
@@ -0,0 +1,102 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm53573.dtsi"
+
+/ {
+	compatible = "luxul,xap-810-v1", "brcm,bcm47189", "brcm,bcm53573";
+	model = "Luxul XAP-810 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds-0 {
+		compatible = "gpio-leds";
+
+		led-5ghz {
+			label = "bcm53xx:blue:5ghz";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-system {
+			label = "bcm53xx:green:system";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	leds-1 {
+		compatible = "gpio-leds";
+
+		led-2ghz {
+			label = "bcm53xx:blue:2ghz";
+			gpios = <&pcie0_chipcommon 3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&pcie0 {
+	ranges = <0x00000000 0 0 0 0 0x00100000>;
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0,0 {
+		reg = <0x0000 0 0 0 0>;
+		ranges = <0x00000000 0 0 0 0 0 0 0x00100000>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,1,0 {
+			reg = <0x0000 0 0 0 0>;
+			ranges = <0x00000000 0 0 0 0x00100000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			pcie0_chipcommon: chipcommon@0 {
+				reg = <0 0x1000>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+	};
+};
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-handle = <&bcm54210e>;
+
+	/delete-node/ fixed-link;
+
+	mdio {
+		/delete-node/ switch@1e;
+
+		bcm54210e: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gmac1 {
+	status = "disabled";
+};
diff --git a/src/arm/broadcom/bcm47189-tenda-ac9.dts b/src/arm/broadcom/bcm47189-tenda-ac9.dts
new file mode 100644
index 0000000..3ac6cac
--- /dev/null
+++ b/src/arm/broadcom/bcm47189-tenda-ac9.dts
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2016 Rafał Miłecki <rafal@milecki.pl>
+ */
+
+/dts-v1/;
+
+#include "bcm53573.dtsi"
+
+/ {
+	compatible = "tenda,ac9", "brcm,bcm47189", "brcm,bcm53573";
+	model = "Tenda AC9";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds-0 {
+		compatible = "gpio-leds";
+
+		led-usb {
+			label = "bcm53xx:blue:usb";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-wps {
+			label = "bcm53xx:blue:wps";
+			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:blue:5ghz";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-system {
+			label = "bcm53xx:blue:system";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	leds-1 {
+		compatible = "gpio-leds";
+
+		led-2ghz {
+			label = "bcm53xx:blue:2ghz";
+			gpios = <&pcie0_chipcommon 3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&pcie0 {
+	ranges = <0x00000000 0 0 0 0 0x00100000>;
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0,0 {
+		reg = <0x0000 0 0 0 0>;
+		ranges = <0x00000000 0 0 0 0 0 0 0x00100000>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,1,0 {
+			reg = <0x0000 0 0 0 0>;
+			ranges = <0x00000000 0 0 0 0x00100000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			pcie0_chipcommon: chipcommon@0 {
+				reg = <0 0x1000>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+	};
+};
+
+&switch {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "wan";
+		};
+
+		port@1 {
+			label = "lan1";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan3";
+		};
+
+		port@4 {
+			label = "lan4";
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm47622.dtsi b/src/arm/broadcom/bcm47622.dtsi
new file mode 100644
index 0000000..7cd38de
--- /dev/null
+++ b/src/arm/broadcom/bcm47622.dtsi
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm47622", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>,
+			<&CA7_2>, <&CA7_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm47622-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm53015-meraki-mr26.dts b/src/arm/broadcom/bcm53015-meraki-mr26.dts
new file mode 100644
index 0000000..0bf5106
--- /dev/null
+++ b/src/arm/broadcom/bcm53015-meraki-mr26.dts
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Meraki MR26 / Codename: Venom
+ *
+ * Copyright (C) 2022 Christian Lamparter <chunkeey@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "meraki,mr26", "brcm,bcm53015", "brcm,bcm4708";
+	model = "Meraki MR26";
+
+	memory@0 {
+		reg = <0x00000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+			panic-indicator;
+		};
+		led-1 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		key-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&uart0 {
+	clock-frequency = <50000000>;
+	/delete-property/ clocks;
+};
+
+&uart1 {
+	status = "disabled";
+};
+
+&gmac0 {
+	status = "okay";
+};
+
+&gmac1 {
+	status = "disabled";
+};
+&gmac2 {
+	status = "disabled";
+};
+&gmac3 {
+	status = "disabled";
+};
+
+&nandcs {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x200000>;
+			read-only;
+		};
+
+		partition@200000 {
+			label = "u-boot-env";
+			reg = <0x200000 0x200000>;
+			/* empty */
+		};
+
+		partition@400000 {
+			label = "u-boot-backup";
+			reg = <0x400000 0x200000>;
+			/* empty */
+		};
+
+		partition@600000 {
+			label = "u-boot-env-backup";
+			reg = <0x600000 0x200000>;
+			/* empty */
+		};
+
+		partition@800000 {
+			label = "ubi";
+			reg = <0x800000 0x7780000>;
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "poe";
+		};
+
+		port@5 {
+			label = "cpu";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_i2c>;
+
+	clock-frequency = <100000>;
+
+	ina219@40 {
+		compatible = "ti,ina219"; /* PoE power */
+		reg = <0x40>;
+		shunt-resistor = <60000>; /* = 60 mOhms */
+	};
+
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+		pagesize = <32>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* it's empty */
+	};
+};
+
+&thermal {
+	status = "disabled";
+	/* does not work, reads 418 degree Celsius */
+};
diff --git a/src/arm/broadcom/bcm53016-dlink-dwl-8610ap.dts b/src/arm/broadcom/bcm53016-dlink-dwl-8610ap.dts
new file mode 100644
index 0000000..c1f5439
--- /dev/null
+++ b/src/arm/broadcom/bcm53016-dlink-dwl-8610ap.dts
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "bcm4709.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "D-Link DWL-8610AP";
+	compatible = "dlink,dwl-8610ap", "brcm,bcm53016", "brcm,bcm4708";
+
+	memory@0 {
+		device_type = "memory";
+		/* 512 MB RAM in 2 x Macronix D9PSH chips */
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led-diag {
+			/* Actually "diag" unclear what this means */
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-wlan-2g {
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wlan-5g {
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			debounce-interval = <100>;
+			wakeup-source;
+			linux,code = <KEY_RESTART>;
+			label = "reset";
+			/* This GPIO is actually stored in NVRAM, but it's not gonna change */
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/*
+	 * Flash memory at 0x1e000000-0x1fffffff
+	 * Macronix 32 64KB blocks; total size 2MB, same that can be
+	 * found attached to the spi_nor SPI controller.
+	 */
+	nvram@1e080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1e080000 0x00020000>;
+
+		et0macaddr: et0macaddr {
+		};
+
+		et1macaddr: et1macaddr {
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&gmac1 {
+	nvmem-cells = <&et1macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	/* Serial SPI NOR Flash MX 25L1606E */
+	status = "okay";
+};
+
+&nandcs {
+	/*
+	 * Spansion S34ML01G100TFI00 128 MB NAND Flash memory
+	 *
+	 * This ECC is a bit unorthodox but it is what the stock firmware
+	 * is using, so to be able to mount the original partitions
+	 * this is necessary.
+	 */
+	nand-ecc-strength = <5>;
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* This is named nflash1.trx in CFE */
+		trx@0 {
+			label = "firmware";
+			reg = <0x00000000 0x02800000>;
+			compatible = "brcm,trx";
+		};
+
+		/* This is named nflash1.trx2 in CFE */
+		trx2@2800000 {
+			label = "firmware2";
+			reg = <0x02800000 0x02800000>;
+			compatible = "brcm,trx";
+		};
+
+		/* This is named nflash1.rwfs in CFE */
+		free@5000000 {
+			label = "free";
+			reg = <0x05000000 0x03000000>;
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm53016-meraki-mr32.dts b/src/arm/broadcom/bcm53016-meraki-mr32.dts
new file mode 100644
index 0000000..25eeacf
--- /dev/null
+++ b/src/arm/broadcom/bcm53016-meraki-mr32.dts
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Meraki MR32 / Codename: Espresso
+ *
+ * Copyright (C) 2018-2020 Christian Lamparter <chunkeey@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "meraki,mr32", "brcm,bcm53016", "brcm,bcm4708";
+	model = "Meraki MR32";
+
+	chosen {
+		bootargs = " console=ttyS0,115200n8 earlycon";
+	};
+
+	memory@0 {
+		reg = <0x00000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	aliases {
+		serial1 = &uart2;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		sysled3 {
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+			panic-indicator;
+		};
+		sysled2 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	pwm-leds {
+		compatible = "pwm-leds";
+
+		led-0 {
+			/* SYS-LED 1 - Tricolor */
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_RED>;
+			pwms = <&pwm 0 50000 0>;
+			max-brightness = <255>;
+		};
+
+		led-1 {
+			/* SYS-LED 1 - Tricolor */
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+			pwms = <&pwm 1 50000 0>;
+			max-brightness = <255>;
+		};
+
+		led-2 {
+			/* SYS-LED 1 - Tricolor */
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_BLUE>;
+			pwms = <&pwm 2 50000 0>;
+			max-brightness = <255>;
+		};
+	};
+};
+
+&uart0 {
+	clock-frequency = <62500000>;
+	/delete-property/ clocks;
+};
+
+&uart1 {
+	status = "disabled";
+};
+
+&uart2 {
+	status = "okay";
+	/*
+	 * bluetooth-le {
+	 *	compatible = "brcm,bcm20732";
+	 *	enable-gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
+	 *};
+	 */
+};
+
+&gmac0 {
+	nvmem-cell-names = "mac-address";
+	nvmem-cells = <&mac_address>;
+};
+
+&gmac1 {
+	status = "disabled";
+};
+&gmac2 {
+	status = "disabled";
+};
+&gmac3 {
+	status = "disabled";
+};
+
+&pwm {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_pwm>;
+};
+
+&nandcs {
+	partitions {
+		/*
+		 * The partition autodetection does not work for this device.
+		 * It will only detect the "nvram" partition with an incorrect size.
+		 *	[    1.721667] 1 bcm47xxpart partitions found on MTD device brcmnand.0
+		 *	[    1.727962] Creating 1 MTD partitions on "brcmnand.0":
+		 *	[    1.733117] 0x000000400000-0x000008000000 : "nvram"
+		 */
+
+		compatible = "fixed-partitions";
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x100000>;
+			read-only;
+		};
+
+		partition@100000 {
+			label = "bootkernel1";
+			reg = <0x100000 0x300000>;
+			read-only;
+		};
+
+		partition@400000 {
+			label = "nvram";
+			reg = <0x400000 0x100000>;
+			read-only;
+		};
+
+		partition@500000 {
+			label = "bootkernel2";
+			reg = <0x500000 0x300000>;
+			read-only;
+		};
+
+		partition@800000 {
+			label = "ubi";
+			reg = <0x800000 0x7780000>;
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "poe";
+		};
+
+		port@5 {
+			label = "cpu";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_i2c>;
+
+	clock-frequency = <100000>;
+
+	current_sense: ina219@45 {
+		compatible = "ti,ina219";
+		reg = <0x45>;
+		shunt-resistor = <60000>; /* = 60 mOhms */
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		mac_address: mac-address@66 {
+			reg = <0x66 0x6>;
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm5301x-nand-cs0-bch1.dtsi b/src/arm/broadcom/bcm5301x-nand-cs0-bch1.dtsi
new file mode 100644
index 0000000..c349e8f
--- /dev/null
+++ b/src/arm/broadcom/bcm5301x-nand-cs0-bch1.dtsi
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom Northstar NAND.
+ *
+ * Copyright (C) 2016 Rafał Miłecki <rafal.milecki@gmail.com>
+ */
+
+#include "bcm5301x-nand-cs0.dtsi"
+
+&nandcs {
+	nand-ecc-algo = "bch";
+	nand-ecc-strength = <1>;
+	nand-ecc-step-size = <512>;
+};
diff --git a/src/arm/broadcom/bcm5301x-nand-cs0-bch4.dtsi b/src/arm/broadcom/bcm5301x-nand-cs0-bch4.dtsi
new file mode 100644
index 0000000..18e25e3
--- /dev/null
+++ b/src/arm/broadcom/bcm5301x-nand-cs0-bch4.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016 Luxul Inc.
+ */
+
+#include "bcm5301x-nand-cs0.dtsi"
+
+&nandcs {
+	nand-ecc-algo = "bch";
+	nand-ecc-strength = <4>;
+	nand-ecc-step-size = <512>;
+};
diff --git a/src/arm/broadcom/bcm5301x-nand-cs0-bch8.dtsi b/src/arm/broadcom/bcm5301x-nand-cs0-bch8.dtsi
new file mode 100644
index 0000000..c8e56d3
--- /dev/null
+++ b/src/arm/broadcom/bcm5301x-nand-cs0-bch8.dtsi
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X Nand chip defaults.
+ *
+ * This should be included if the NAND controller is on chip select 0
+ * and uses 8 bit ECC.
+ *
+ * Copyright (C) 2015 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+#include "bcm5301x-nand-cs0.dtsi"
+
+&nandcs {
+	nand-ecc-algo = "bch";
+	nand-ecc-strength = <8>;
+	nand-ecc-step-size = <512>;
+};
diff --git a/src/arm/broadcom/bcm5301x-nand-cs0.dtsi b/src/arm/broadcom/bcm5301x-nand-cs0.dtsi
new file mode 100644
index 0000000..be9a00f
--- /dev/null
+++ b/src/arm/broadcom/bcm5301x-nand-cs0.dtsi
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom Northstar NAND.
+ *
+ * Copyright (C) 2015 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+/ {
+	nand-controller@18028000 {
+		nandcs: nand@0 {
+			compatible = "brcm,nandcs";
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partitions {
+				compatible = "brcm,bcm947xx-cfe-partitions";
+			};
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm5301x.dtsi b/src/arm/broadcom/bcm5301x.dtsi
new file mode 100644
index 0000000..f06a178
--- /dev/null
+++ b/src/arm/broadcom/bcm5301x.dtsi
@@ -0,0 +1,136 @@
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * Generic DTS part for all BCM53010, BCM53011, BCM53012, BCM53014, BCM53015,
+ * BCM53016, BCM53017, BCM53018, BCM4707, BCM4708 and BCM4709 SoCs
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include "bcm-ns.dtsi"
+
+/ {
+	mpcore-bus@19000000 {
+		a9pll: arm_clk@0 {
+			#clock-cells = <0>;
+			compatible = "brcm,nsp-armpll";
+			clocks = <&osc>;
+			reg = <0x00000 0x1000>;
+		};
+
+		watchdog@20620 {
+			compatible = "arm,cortex-a9-twd-wdt";
+			reg = <0x20620 0x20>;
+			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
+						  IRQ_TYPE_EDGE_RISING)>;
+			clocks = <&periph_clk>;
+		};
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc: oscillator {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <25000000>;
+		};
+
+		iprocmed: iprocmed {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
+			clock-div = <2>;
+			clock-mult = <1>;
+		};
+
+		iprocslow: iprocslow {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		periph_clk: periph_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&a9pll>;
+			clock-div = <2>;
+			clock-mult = <1>;
+		};
+	};
+
+	i2c0: i2c@18009000 {
+		compatible = "brcm,iproc-i2c";
+		reg = <0x18009000 0x50>;
+		interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clock-frequency = <100000>;
+		status = "disabled";
+	};
+
+	dmu-bus@1800c000 {
+		cru-bus@100 {
+			lcpll0: clock-controller@100 {
+				#clock-cells = <1>;
+				compatible = "brcm,nsp-lcpll0";
+				reg = <0x100 0x14>;
+				clocks = <&osc>;
+				clock-output-names = "lcpll0", "pcie_phy",
+						     "sdio", "ddr_phy";
+			};
+
+			genpll: clock-controller@140 {
+				#clock-cells = <1>;
+				compatible = "brcm,nsp-genpll";
+				reg = <0x140 0x24>;
+				clocks = <&osc>;
+				clock-output-names = "genpll", "phy",
+						     "ethernetclk",
+						     "usbclk", "iprocfast",
+						     "sata1", "sata2";
+			};
+		};
+	};
+
+	spi@18029200 {
+		compatible = "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi";
+		reg = <0x18029200 0x184>,
+		      <0x18029000 0x124>,
+		      <0x1811b408 0x004>,
+		      <0x180293a0 0x01c>;
+		reg-names = "mspi", "bspi", "intr_regs", "intr_status_reg";
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "mspi_done",
+				  "mspi_halted",
+				  "spi_lr_fullness_reached",
+				  "spi_lr_session_aborted",
+				  "spi_lr_impatient",
+				  "spi_lr_session_done",
+				  "spi_lr_overread";
+		clocks = <&iprocmed>;
+		num-cs = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		spi_nor: flash@0 {
+			compatible = "jedec,spi-nor";
+			reg = <0>;
+			spi-max-frequency = <20000000>;
+			status = "disabled";
+
+			partitions {
+				compatible = "brcm,bcm947xx-cfe-partitions";
+			};
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm53340-ubnt-unifi-switch8.dts b/src/arm/broadcom/bcm53340-ubnt-unifi-switch8.dts
new file mode 100644
index 0000000..975f854
--- /dev/null
+++ b/src/arm/broadcom/bcm53340-ubnt-unifi-switch8.dts
@@ -0,0 +1,86 @@
+/*
+ * DTS for Unifi Switch 8 port
+ *
+ * Copyright (C) 2017 Florian Fainelli <f.fainelli@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm-hr2.dtsi"
+
+/ {
+	compatible = "ubnt,unifi-switch8", "brcm,bcm53342", "brcm,hr2";
+	model = "Ubiquiti UniFi Switch 8 (BCM53342)";
+
+	/* Hurricane 2 designs use the second UART */
+	chosen {
+		bootargs = "console=ttyS1,115200 earlyprintk";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x68000000 0x08000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+	bspi-sel = <0>;
+
+	flash: flash@0 {
+		compatible = "m25p80";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <12500000>;
+		spi-cpol;
+		spi-cpha;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0xc0000>;
+		};
+
+		partition@c0000 {
+			label = "u-boot-env";
+			reg = <0xc0000 0x10000>;
+		};
+
+		partition@d0000 {
+			label = "shmoo";
+			reg = <0xd0000 0x10000>;
+		};
+
+		partition@e0000 {
+			label = "kernel0";
+			reg = <0xe0000 0xf00000>;
+		};
+
+		partition@fe0000 {
+			label = "kernel1";
+			reg = <0xfe0000 0xf10000>;
+		};
+
+		partition@1ef0000 {
+			label = "cfg";
+			reg = <0x1ef0000 0x100000>;
+		};
+
+		partition@1ff0000 {
+			label = "EEPROM";
+			reg = <0x1ff0000 0x10000>;
+		};
+	};
+};
+
+&pcie0 {
+	/* Attaches to the internal switch */
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm53573.dtsi b/src/arm/broadcom/bcm53573.dtsi
new file mode 100644
index 0000000..2df8074
--- /dev/null
+++ b/src/arm/broadcom/bcm53573.dtsi
@@ -0,0 +1,266 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2016 Rafał Miłecki <rafal@milecki.pl>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&gic>;
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+		};
+	};
+
+	mpcore@18310000 {
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x18310000 0x00008000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+			      <0x2000 0x0100>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		alp: oscillator {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <40000000>;
+		};
+	};
+
+	axi@18000000 {
+		compatible = "brcm,bus-axi";
+		reg = <0x18000000 0x1000>;
+		ranges = <0x00000000 0x18000000 0x00100000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0x000fffff 0xffff>;
+		interrupt-map =
+			/* ChipCommon */
+			<0x00000000 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* IEEE 802.11 0 */
+			<0x00001000 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* PCIe Controller 0 */
+			<0x00002000 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00002000 1 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00002000 2 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00002000 3 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00002000 4 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00002000 5 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* USB 2.0 Controller */
+			<0x00004000 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* Ethernet Controller 0 */
+			<0x00005000 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* IEEE 802.11 1 */
+			<0x0000a000 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* Ethernet Controller 1 */
+			<0x0000b000 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+
+		chipcommon: chipcommon@0 {
+			compatible = "simple-bus";
+			reg = <0x00000000 0x1000>;
+			ranges;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			uart0: serial@300 {
+				compatible = "ns16550a";
+				reg = <0x0300 0x100>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_PPI 16 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&alp>;
+				status = "okay";
+			};
+		};
+
+		pcie0: pcie@2000 {
+			reg = <0x00002000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+		};
+
+		usb2: usb2@4000 {
+			reg = <0x4000 0x1000>;
+			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ehci: usb@4000 {
+				compatible = "generic-ehci";
+				reg = <0x4000 0x1000>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ehci_port1: port@1 {
+					reg = <1>;
+					#trigger-source-cells = <0>;
+				};
+
+				ehci_port2: port@2 {
+					reg = <2>;
+					#trigger-source-cells = <0>;
+				};
+			};
+
+			ohci: usb@d000 {
+				compatible = "generic-ohci";
+				reg = <0xd000 0x1000>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ohci_port1: port@1 {
+					reg = <1>;
+					#trigger-source-cells = <0>;
+				};
+
+				ohci_port2: port@2 {
+					reg = <2>;
+					#trigger-source-cells = <0>;
+				};
+			};
+		};
+
+		gmac0: ethernet@5000 {
+			reg = <0x5000 0x1000>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch: switch@1e {
+					compatible = "brcm,bcm53125";
+					reg = <0x1e>;
+
+					status = "disabled";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+						};
+
+						port@1 {
+							reg = <1>;
+						};
+
+						port@2 {
+							reg = <2>;
+						};
+
+						port@3 {
+							reg = <3>;
+						};
+
+						port@4 {
+							reg = <4>;
+						};
+
+						port@5 {
+							reg = <5>;
+							ethernet = <&gmac1>;
+
+							fixed-link {
+								speed = <1000>;
+								full-duplex;
+							};
+						};
+
+						port@8 {
+							reg = <8>;
+							ethernet = <&gmac0>;
+						};
+					};
+				};
+			};
+		};
+
+		gmac1: ethernet@b000 {
+			reg = <0xb000 0x1000>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		pmu@12000 {
+			compatible = "simple-mfd", "syscon";
+			reg = <0x00012000 0x00001000>;
+
+			ilp: ilp {
+				compatible = "brcm,bcm53573-ilp";
+				clocks = <&alp>;
+				#clock-cells = <0>;
+				clock-output-names = "ilp";
+			};
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm59056.dtsi b/src/arm/broadcom/bcm59056.dtsi
new file mode 100644
index 0000000..a9bb7ad
--- /dev/null
+++ b/src/arm/broadcom/bcm59056.dtsi
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+* Copyright 2014 Linaro Limited
+* Author: Matt Porter <mporter@linaro.org>
+*/
+
+&pmu {
+	compatible = "brcm,bcm59056";
+	regulators {
+		rfldo_reg: rfldo {
+		};
+
+		camldo1_reg: camldo1 {
+		};
+
+		camldo2_reg: camldo2 {
+		};
+
+		simldo1_reg: simldo1 {
+		};
+
+		simldo2_reg: simldo2 {
+		};
+
+		sdldo_reg: sdldo {
+		};
+
+		sdxldo_reg: sdxldo {
+		};
+
+		mmcldo1_reg: mmcldo1 {
+		};
+
+		mmcldo2_reg: mmcldo2 {
+		};
+
+		audldo_reg: audldo {
+		};
+
+		micldo_reg: micldo {
+		};
+
+		usbldo_reg: usbldo {
+		};
+
+		vibldo_reg: vibldo {
+		};
+
+		csr_reg: csr {
+		};
+
+		iosr1_reg: iosr1 {
+		};
+
+		iosr2_reg: iosr2 {
+		};
+
+		msr_reg: msr {
+		};
+
+		sdsr1_reg: sdsr1 {
+		};
+
+		sdsr2_reg: sdsr2 {
+		};
+
+		vsr_reg: vsr {
+		};
+
+		gpldo1_reg: gpldo1 {
+		};
+
+		gpldo2_reg: gpldo2 {
+		};
+
+		gpldo3_reg: gpldo3 {
+		};
+
+		gpldo4_reg: gpldo4 {
+		};
+
+		gpldo5_reg: gpldo5 {
+		};
+
+		gpldo6_reg: gpldo6 {
+		};
+
+		vbus_reg: vbus {
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm63138.dtsi b/src/arm/broadcom/bcm63138.dtsi
new file mode 100644
index 0000000..93281c4
--- /dev/null
+++ b/src/arm/broadcom/bcm63138.dtsi
@@ -0,0 +1,247 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Broadcom BCM63138 DSL SoCs Device Tree
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm63138", "brcm,bcmbca";
+	model = "Broadcom BCM963138 Reference Board";
+	interrupt-parent = <&gic>;
+
+	aliases {
+		uart0 = &serial0;
+		uart1 = &serial1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			reg = <0>;
+			enable-method = "brcm,bcm63138";
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			reg = <1>;
+			enable-method = "brcm,bcm63138";
+			resets = <&pmb0 4 1>;
+		};
+	};
+
+	clocks {
+		/* UBUS peripheral clock */
+		periph_clk: periph_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <50000000>;
+			clock-output-names = "periph";
+		};
+
+		/* peripheral clock for system timer */
+		axi_clk: axi_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&armpll>;
+			clock-div = <2>;
+			clock-mult = <1>;
+		};
+
+		/* APB bus clock */
+		apb_clk: apb_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&armpll>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <400000000>;
+		};
+	};
+
+	/* ARM bus */
+	axi@80000000 {
+		compatible = "simple-bus";
+		ranges = <0 0x80000000 0x784000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		L2: cache-controller@1d000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x1d000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+			cache-size = <524288>;
+			cache-sets = <1024>;
+			cache-line-size = <32>;
+			interrupts = <GIC_PPI 0 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		scu: scu@1e000 {
+			compatible = "arm,cortex-a9-scu";
+			reg = <0x1e000 0x100>;
+		};
+
+		gic: interrupt-controller@1f000 {
+			compatible = "arm,cortex-a9-gic";
+			reg = <0x1f000 0x1000
+				0x1e100 0x100>;
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+		};
+
+		global_timer: timer@1e200 {
+			compatible = "arm,cortex-a9-global-timer";
+			reg = <0x1e200 0x20>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&axi_clk>;
+		};
+
+		local_timer: local-timer@1e600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0x1e600 0x20>;
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
+						  IRQ_TYPE_EDGE_RISING)>;
+			clocks = <&axi_clk>;
+		};
+
+		twd_watchdog: watchdog@1e620 {
+			compatible = "arm,cortex-a9-twd-wdt";
+			reg = <0x1e620 0x20>;
+			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
+						  IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		armpll: armpll@20000 {
+			#clock-cells = <0>;
+			compatible = "brcm,bcm63138-armpll";
+			clocks = <&periph_clk>;
+			reg = <0x20000 0xf00>;
+		};
+
+		pmb0: reset-controller@4800c0 {
+			compatible = "brcm,bcm63138-pmb";
+			reg = <0x4800c0 0x10>;
+			#reset-cells = <2>;
+		};
+
+		pmb1: reset-controller@4800e0 {
+			compatible = "brcm,bcm63138-pmb";
+			reg = <0x4800e0 0x10>;
+			#reset-cells = <2>;
+		};
+
+		ahci: sata@a000 {
+			compatible = "brcm,bcm63138-ahci", "brcm,sata3-ahci";
+			reg-names = "ahci", "top-ctrl";
+			reg = <0xa000 0x9ac>, <0x8040 0x24>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&pmb0 3 1>;
+			reset-names = "ahci";
+			status = "disabled";
+
+			sata0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata_phy0>;
+			};
+		};
+
+		sata_phy: sata-phy@8100 {
+			compatible = "brcm,bcm63138-sata-phy", "brcm,phy-sata3";
+			reg = <0x8100 0x1e00>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+		};
+	};
+
+	/* Legacy UBUS base */
+	ubus@fffe8000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xfffe8000 0x8100>;
+
+		timer: timer@80 {
+			compatible = "brcm,bcm6328-timer", "syscon";
+			reg = <0x80 0x3c>;
+		};
+
+		serial0: serial@600 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x600 0x1b>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "periph";
+			status = "disabled";
+		};
+
+		serial1: serial@620 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x620 0x1b>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "periph";
+			status = "disabled";
+		};
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		nand_controller: nand-controller@2000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.0", "brcm,brcmnand";
+			reg = <0x2000 0x600>, <0xf0 0x10>;
+			reg-names = "nand", "nand-int-base";
+			status = "disabled";
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "nand";
+		};
+
+		bootlut: bootlut@8000 {
+			compatible = "brcm,bcm63138-bootlut";
+			reg = <0x8000 0x50>;
+		};
+
+		reboot {
+			compatible = "syscon-reboot";
+			regmap = <&timer>;
+			offset = <0x34>;
+			mask = <1>;
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm63148.dtsi b/src/arm/broadcom/bcm63148.dtsi
new file mode 100644
index 0000000..24431de
--- /dev/null
+++ b/src/arm/broadcom/bcm63148.dtsi
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm63148", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		B15_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b15";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B15_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b15";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a15-pmu";
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B15_0>, <&B15_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <400000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@80030000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x80030000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a15-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+					IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xfffe8000 0x8000>;
+
+		uart0: serial@600 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x600 0x20>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63148-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm63178.dtsi b/src/arm/broadcom/bcm63178.dtsi
new file mode 100644
index 0000000..3f9aed9
--- /dev/null
+++ b/src/arm/broadcom/bcm63178.dtsi
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm63178", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>,
+			<&CA7_2>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63178-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm6756.dtsi b/src/arm/broadcom/bcm6756.dtsi
new file mode 100644
index 0000000..1d8d957
--- /dev/null
+++ b/src/arm/broadcom/bcm6756.dtsi
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6756", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>,
+			<&CA7_2>, <&CA7_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6756-hsspi", "brcm,bcmbca-hsspi-v1.1";
+			reg = <0x1000 0x600>, <0x2610 0x4>;
+			reg-names = "hsspi", "spim-ctrl";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm6846.dtsi b/src/arm/broadcom/bcm6846.dtsi
new file mode 100644
index 0000000..cf92cf8
--- /dev/null
+++ b/src/arm/broadcom/bcm6846.dtsi
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6846", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <400000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		uart0: serial@640 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x640 0x1b>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6846-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm6855.dtsi b/src/arm/broadcom/bcm6855.dtsi
new file mode 100644
index 0000000..52d6bc8
--- /dev/null
+++ b/src/arm/broadcom/bcm6855.dtsi
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6855", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>, <&CA7_2>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6855-hsspi", "brcm,bcmbca-hsspi-v1.1";
+			reg = <0x1000 0x600>, <0x2610 0x4>;
+			reg-names = "hsspi", "spim-ctrl";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm6878.dtsi b/src/arm/broadcom/bcm6878.dtsi
new file mode 100644
index 0000000..2c5d706
--- /dev/null
+++ b/src/arm/broadcom/bcm6878.dtsi
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6878", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+					IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6878-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm7445-bcm97445svmb.dts b/src/arm/broadcom/bcm7445-bcm97445svmb.dts
new file mode 100644
index 0000000..f92d2cf
--- /dev/null
+++ b/src/arm/broadcom/bcm7445-bcm97445svmb.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm7445.dtsi"
+
+/ {
+	model = "Broadcom STB (bcm7445), SVMB reference board";
+	compatible = "brcm,bcm7445", "brcm,brcmstb";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00 0x00000000 0x00 0x40000000>,
+		      <0x00 0x40000000 0x00 0x40000000>,
+		      <0x00 0x80000000 0x00 0x40000000>;
+	};
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand@1 {
+		compatible = "brcm,nandcs";
+		reg = <1>;
+		nand-ecc-step-size = <512>;
+		nand-ecc-strength = <8>;
+		nand-on-flash-bbt;
+
+		#size-cells = <2>;
+		#address-cells = <2>;
+
+		flash1.rootfs0@0 {
+			reg = <0x0 0x0 0x0 0x80000000>;
+		};
+
+		flash1.rootfs1@80000000 {
+			reg = <0x0 0x80000000 0x0 0x80000000>;
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm7445.dtsi b/src/arm/broadcom/bcm7445.dtsi
new file mode 100644
index 0000000..5ac2042
--- /dev/null
+++ b/src/arm/broadcom/bcm7445.dtsi
@@ -0,0 +1,315 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	model = "Broadcom STB (bcm7445)";
+	compatible = "brcm,bcm7445", "brcm,brcmstb";
+	interrupt-parent = <&gic>;
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "brcm,brahma-b15";
+			device_type = "cpu";
+			enable-method = "brcm,brahma-b15";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,brahma-b15";
+			device_type = "cpu";
+			enable-method = "brcm,brahma-b15";
+			reg = <1>;
+		};
+
+		cpu@2 {
+			compatible = "brcm,brahma-b15";
+			device_type = "cpu";
+			enable-method = "brcm,brahma-b15";
+			reg = <2>;
+		};
+
+		cpu@3 {
+			compatible = "brcm,brahma-b15";
+			device_type = "cpu";
+			enable-method = "brcm,brahma-b15";
+			reg = <3>;
+		};
+	};
+
+	gic: interrupt-controller@ffd00000 {
+		compatible = "brcm,brahma-b15-gic", "arm,cortex-a15-gic";
+		reg = <0x00 0xffd01000 0x00 0x1000>,
+		      <0x00 0xffd02000 0x00 0x2000>,
+		      <0x00 0xffd04000 0x00 0x2000>,
+		      <0x00 0xffd06000 0x00 0x2000>;
+		interrupt-controller;
+		#interrupt-cells = <3>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	rdb@f0000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0 0x00 0xf0000000 0x1000000>;
+
+		serial@40ab00 {
+			compatible = "ns16550a";
+			reg = <0x40ab00 0x20>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <81000000>;
+		};
+
+		sun_top_ctrl: syscon@404000 {
+			compatible = "brcm,bcm7445-sun-top-ctrl",
+				     "syscon";
+			reg = <0x404000 0x51c>;
+		};
+
+		hif_cpubiuctrl: syscon@3e2400 {
+			compatible = "brcm,bcm7445-hif-cpubiuctrl",
+				     "syscon";
+			reg = <0x3e2400 0x5b4>;
+		};
+
+		hif_continuation: syscon@452000 {
+			compatible = "brcm,bcm7445-hif-continuation",
+				     "syscon";
+			reg = <0x452000 0x100>;
+		};
+
+		irq0_intc: interrupt-controller@40a780 {
+			compatible = "brcm,bcm7120-l2-intc";
+			interrupt-parent = <&gic>;
+			#interrupt-cells = <1>;
+			reg = <0x40a780 0x8>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 0x45 0x0>,
+				     <GIC_SPI 0x43 0x0>;
+			brcm,int-map-mask = <0x25c>, <0x7000000>;
+			brcm,int-fwd-mask = <0x70000>;
+		};
+
+		irq0_aon_intc: interrupt-controller@417280 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x417280 0x8>;
+			interrupt-parent = <&gic>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 0x46 0x0>,
+				     <GIC_SPI 0x44 0x0>,
+				     <GIC_SPI 0x49 0x0>;
+			brcm,int-map-mask = <0x1e3 0x18000000 0x100000>;
+			brcm,int-fwd-mask = <0x0>;
+			brcm,irq-can-wake;
+		};
+
+		hif_intr2_intc: interrupt-controller@3e1000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x3e1000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupts = <GIC_SPI 0x20 0x0>;
+			interrupt-parent = <&gic>;
+			interrupt-names = "hif";
+		};
+
+                aon_pm_l2_intc: interrupt-controller@410640 {
+			compatible = "brcm,l2-intc";
+			reg = <0x410640 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupts = <GIC_SPI 0x40 0x0>;
+			interrupt-parent = <&gic>;
+			brcm,irq-can-wake;
+		};
+
+		aon-ctrl@410000 {
+			compatible = "brcm,brcmstb-aon-ctrl";
+			reg = <0x410000 0x200>, <0x410200 0x400>;
+			reg-names = "aon-ctrl", "aon-sram";
+		};
+
+		nand_controller: nand-controller@3e2800 {
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,brcmnand-v7.1", "brcm,brcmnand";
+			reg-names = "nand", "flash-dma";
+			reg = <0x3e2800 0x600>, <0x3e3000 0x2c>;
+			interrupt-parent = <&hif_intr2_intc>;
+			interrupts = <24>, <4>;
+			interrupt-names = "nand_ctlrdy", "flash_dma_done";
+		};
+
+		sata@45a000 {
+			compatible = "brcm,bcm7445-ahci", "brcm,sata3-ahci";
+			reg-names = "ahci", "top-ctrl";
+			reg = <0x45a000 0xa9c>, <0x458040 0x24>;
+			interrupts = <GIC_SPI 30 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			sata0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata_phy0>;
+			};
+
+			sata1: sata-port@1 {
+				reg = <1>;
+				phys = <&sata_phy1>;
+			};
+		};
+
+		sata_phy: sata-phy@458100 {
+			compatible = "brcm,bcm7445-sata-phy", "brcm,phy-sata3";
+			reg = <0x458100 0x1f00>;
+			reg-names = "phy";
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+
+			sata_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+
+			sata_phy1: sata-phy@1 {
+				reg = <1>;
+				#phy-cells = <0>;
+			};
+		};
+
+		upg_gio: gpio@40a700 {
+			compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
+			reg = <0x40a700 0x80>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&irq0_intc>;
+			interrupts = <6>;
+			brcm,gpio-bank-widths = <32 32 32 24>;
+		};
+
+		upg_gio_aon: gpio@4172c0 {
+			compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
+			reg = <0x4172c0 0x40>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupts-extended = <&irq0_aon_intc 0x6>,
+					      <&aon_pm_l2_intc 0x5>;
+			wakeup-source;
+			brcm,gpio-bank-widths = <18 4>;
+		};
+
+	};
+
+	memory_controllers@f1100000 {
+		compatible = "simple-bus";
+		ranges = <0x0 0x0 0xf1100000 0x200000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		memc@0 {
+			compatible = "brcm,brcmstb-memc", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0x80000>;
+
+			memc-ddr@2000 {
+				compatible = "brcm,brcmstb-memc-ddr";
+				reg = <0x2000 0x800>;
+			};
+
+			ddr-phy@6000 {
+				compatible = "brcm,brcmstb-ddr-phy-v240.1";
+				reg = <0x6000 0x21c>;
+				};
+
+			shimphy@8000 {
+				compatible = "brcm,brcmstb-ddr-shimphy-v1.0";
+				reg = <0x8000 0xe4>;
+			};
+		};
+
+		memc@80000 {
+			compatible = "brcm,brcmstb-memc", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x80000 0x80000>;
+
+			memc-ddr@2000 {
+				compatible = "brcm,brcmstb-memc-ddr";
+				reg = <0x2000 0x800>;
+			};
+
+			ddr-phy@6000 {
+				compatible = "brcm,brcmstb-ddr-phy-v240.1";
+				reg = <0x6000 0x21c>;
+			};
+
+			shimphy@8000 {
+				compatible = "brcm,brcmstb-ddr-shimphy-v1.0";
+				reg = <0x8000 0xe4>;
+			};
+		};
+
+		memc@100000 {
+			compatible = "brcm,brcmstb-memc", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x100000 0x80000>;
+
+			memc-ddr@2000 {
+				compatible = "brcm,brcmstb-memc-ddr";
+				reg = <0x2000 0x800>;
+			};
+
+			ddr-phy@6000 {
+				compatible = "brcm,brcmstb-ddr-phy-v240.1";
+				reg = <0x6000 0x21c>;
+			};
+
+			shimphy@8000 {
+				compatible = "brcm,brcmstb-ddr-shimphy-v1.0";
+				reg = <0x8000 0xe4>;
+			};
+		};
+	};
+
+	sram@ffe00000 {
+		compatible = "brcm,boot-sram", "mmio-sram";
+		reg = <0x0 0xffe00000 0x0 0x10000>;
+	};
+
+	smpboot {
+		compatible = "brcm,brcmstb-smpboot";
+		syscon-cpu = <&hif_cpubiuctrl 0x88 0x178>;
+		syscon-cont = <&hif_continuation>;
+	};
+
+	reboot {
+		compatible = "brcm,brcmstb-reboot";
+		syscon = <&sun_top_ctrl 0x304 0x308>;
+	};
+};
diff --git a/src/arm/broadcom/bcm911360_entphn.dts b/src/arm/broadcom/bcm911360_entphn.dts
new file mode 100644
index 0000000..363009e
--- /dev/null
+++ b/src/arm/broadcom/bcm911360_entphn.dts
@@ -0,0 +1,99 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2014 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-cygnus.dtsi"
+#include "dt-bindings/input/input.h"
+
+/ {
+	model = "Cygnus Enterprise Phone (BCM911360_ENTPHN)";
+	compatible = "brcm,bcm11360", "brcm,cygnus";
+
+	aliases {
+		serial0 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-hook {
+			label = "HOOK";
+			linux,code = <KEY_O>;
+			gpios = <&gpio_asiu 48 0>;
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+};
+
+&switch {
+	status = "okay";
+};
+
+&v3d {
+	assigned-clocks =
+		<&mipipll BCM_CYGNUS_MIPIPLL>,
+		<&mipipll BCM_CYGNUS_MIPIPLL_CH2_V3D>;
+	assigned-clock-rates = <525000000>, <300000000>;
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&nand_controller {
+	nand@1 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+	};
+};
diff --git a/src/arm/broadcom/bcm911360k.dts b/src/arm/broadcom/bcm911360k.dts
new file mode 100644
index 0000000..091c73a
--- /dev/null
+++ b/src/arm/broadcom/bcm911360k.dts
@@ -0,0 +1,52 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2014 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-cygnus.dtsi"
+
+/ {
+	model = "Cygnus SVK (BCM911360K)";
+	compatible = "brcm,bcm11360", "brcm,cygnus";
+
+	aliases {
+		serial0 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&uart3 {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm94708.dts b/src/arm/broadcom/bcm94708.dts
new file mode 100644
index 0000000..d9eb204
--- /dev/null
+++ b/src/arm/broadcom/bcm94708.dts
@@ -0,0 +1,49 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2015 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+
+/ {
+	model = "NorthStar SVK (BCM94708)";
+	compatible = "brcm,bcm94708", "brcm,bcm4708";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm94709.dts b/src/arm/broadcom/bcm94709.dts
new file mode 100644
index 0000000..618c812
--- /dev/null
+++ b/src/arm/broadcom/bcm94709.dts
@@ -0,0 +1,49 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2015 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+
+/ {
+	model = "NorthStar SVK (BCM94709)";
+	compatible = "brcm,bcm94709", "brcm,bcm4709", "brcm,bcm4708";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm947189acdbmr.dts b/src/arm/broadcom/bcm947189acdbmr.dts
new file mode 100644
index 0000000..0b8727a
--- /dev/null
+++ b/src/arm/broadcom/bcm947189acdbmr.dts
@@ -0,0 +1,96 @@
+/*
+ * Copyright (C) 2017 Broadcom
+ * Author: Florian Fainelli <f.fainelli@gmail.com>
+ *
+ * Licensed under the ISC license.
+ */
+
+/dts-v1/;
+
+#include "bcm53573.dtsi"
+
+/ {
+	compatible = "brcm,bcm947189acdbmr", "brcm,bcm47189", "brcm,bcm53573";
+	model = "Broadcom BCM947189ACDBMR";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-wps {
+			label = "bcm53xx:blue:wps";
+			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:blue:5ghz";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2ghz {
+			label = "bcm53xx:blue:2ghz";
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		num-chipselects = <1>;
+		sck-gpios = <&chipcommon 21 0>;
+		miso-gpios = <&chipcommon 22 0>;
+		mosi-gpios = <&chipcommon 23 0>;
+		cs-gpios = <&chipcommon 24 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* External BCM6802 MoCA chip is connected */
+	};
+};
+
+&pcie0 {
+	ranges = <0x00000000 0 0 0 0 0x00100000>;
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0,0 {
+		reg = <0x0000 0 0 0 0>;
+		ranges = <0x00000000 0 0 0 0 0 0 0x00100000>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,1,0 {
+			reg = <0x0000 0 0 0 0>;
+			ranges = <0x00000000 0 0 0 0x00100000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
+};
diff --git a/src/arm/broadcom/bcm947622.dts b/src/arm/broadcom/bcm947622.dts
new file mode 100644
index 0000000..93b8ce2
--- /dev/null
+++ b/src/arm/broadcom/bcm947622.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm47622.dtsi"
+
+/ {
+	model = "Broadcom BCM947622 Reference Board";
+	compatible = "brcm,bcm947622", "brcm,bcm47622", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm953012er.dts b/src/arm/broadcom/bcm953012er.dts
new file mode 100644
index 0000000..d939ec9
--- /dev/null
+++ b/src/arm/broadcom/bcm953012er.dts
@@ -0,0 +1,100 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom. All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	model = "NorthStar Enterprise Router (BCM953012ER)";
+	compatible = "brcm,bcm953012er", "brcm,bcm53012", "brcm,bcm4708";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+		};
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			reg = <0>;
+			label = "port0";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "port1";
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm953012hr.dts b/src/arm/broadcom/bcm953012hr.dts
new file mode 100644
index 0000000..b070b69
--- /dev/null
+++ b/src/arm/broadcom/bcm953012hr.dts
@@ -0,0 +1,102 @@
+/*
+ *  SPDX-License-Identifier: BSD-3-Clause
+ *
+ *  Copyright(c) 2017 Broadcom
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom nor the names of its contributors
+ *      may be used to endorse or promote products derived from this
+ *      software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch4.dtsi"
+
+/ {
+	model = "NorthStar HR (BCM953012HR)";
+	compatible = "brcm,bcm953012hr", "brcm,bcm53012", "brcm,bcm4708";
+
+	aliases {
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+		ethernet2 = &gmac2;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+};
+
+&nandcs {
+	partition@0 {
+		label = "nboot";
+		reg = <0x00000000 0x00200000>;
+		read-only;
+	};
+	partition@200000 {
+		label = "nenv";
+		reg = <0x00200000 0x00400000>;
+	};
+	partition@600000 {
+		label = "nsystem";
+		reg = <0x00600000 0x00a00000>;
+	};
+	partition@1000000 {
+		label = "nrootfs";
+		reg = <0x01000000 0x07000000>;
+	};
+};
+
+&spi_nor {
+	status = "okay";
+	spi-max-frequency = <62500000>;
+	m25p,default-addr-width = <3>;
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	partition@0 {
+		label = "boot";
+		reg = <0x00000000 0x000d0000>;
+	};
+	partition@d000 {
+		label = "env";
+		reg = <0x000d0000 0x00030000>;
+	};
+	partition@100000 {
+		label = "system";
+		reg = <0x00100000 0x00600000>;
+	};
+	partition@700000 {
+		label = "rootfs";
+		reg = <0x00700000 0x00900000>;
+	};
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm953012k.dts b/src/arm/broadcom/bcm953012k.dts
new file mode 100644
index 0000000..f1e6bca
--- /dev/null
+++ b/src/arm/broadcom/bcm953012k.dts
@@ -0,0 +1,120 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2015 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+
+/ {
+	model = "NorthStar SVK (BCM953012K)";
+	compatible = "brcm,bcm953012k", "brcm,bcm53012", "brcm,bcm4708";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+};
+
+&nand_controller {
+	nand@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+
+		partition@0 {
+			label = "nboot";
+			reg = <0x00000000 0x00200000>;
+			read-only;
+		};
+		partition@200000 {
+			label = "nenv";
+			reg = <0x00200000 0x00400000>;
+		};
+		partition@600000 {
+			label = "nsystem";
+			reg = <0x00600000 0x00a00000>;
+		};
+		partition@1000000 {
+			label = "nrootfs";
+			reg = <0x01000000 0x07000000>;
+		};
+	};
+};
+
+&spi_nor {
+	status = "okay";
+	spi-max-frequency = <62500000>;
+	m25p,default-addr-width = <3>;
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	partition@0 {
+		label = "boot";
+		reg = <0x00000000 0x000d0000>;
+	};
+	partition@d000 {
+		label = "env";
+		reg = <0x000d0000 0x00030000>;
+	};
+	partition@100000 {
+		label = "system";
+		reg = <0x00100000 0x00600000>;
+	};
+	partition@700000 {
+		label = "rootfs";
+		reg = <0x00700000 0x00900000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm958300k.dts b/src/arm/broadcom/bcm958300k.dts
new file mode 100644
index 0000000..dda3e11
--- /dev/null
+++ b/src/arm/broadcom/bcm958300k.dts
@@ -0,0 +1,77 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2014 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-cygnus.dtsi"
+#include "bcm9hmidc.dtsi"
+
+/ {
+	model = "Cygnus SVK (BCM958300K)";
+	compatible = "brcm,bcm58300", "brcm,cygnus";
+
+	aliases {
+		serial0 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&nand_controller {
+	nand@1 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+	};
+};
diff --git a/src/arm/broadcom/bcm958305k.dts b/src/arm/broadcom/bcm958305k.dts
new file mode 100644
index 0000000..ea3c6b8
--- /dev/null
+++ b/src/arm/broadcom/bcm958305k.dts
@@ -0,0 +1,85 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2015 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-cygnus.dtsi"
+#include "bcm9hmidc.dtsi"
+
+/ {
+	model = "Cygnus Wireless Audio (BCM958305K)";
+	compatible = "brcm,bcm58305", "brcm,cygnus";
+
+	aliases {
+		serial0 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&nand_controller {
+	nand@1 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+	};
+};
diff --git a/src/arm/broadcom/bcm958522er.dts b/src/arm/broadcom/bcm958522er.dts
new file mode 100644
index 0000000..15f0236
--- /dev/null
+++ b/src/arm/broadcom/bcm958522er.dts
@@ -0,0 +1,185 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-nsp.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "NorthStar Plus SVK (BCM958522ER)";
+	compatible = "brcm,bcm958522er", "brcm,bcm58522", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+		open-source;
+		priority = <200>;
+	};
+};
+
+/* USB 3 support needed to be complete */
+
+&dma {
+	status = "okay";
+};
+
+&amac0 {
+	status = "okay";
+};
+
+&amac1 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&nand_controller {
+	nand@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+
+		partition@0 {
+			label = "nboot";
+			reg = <0x00000000 0x00200000>;
+			read-only;
+		};
+		partition@200000 {
+			label = "nenv";
+			reg = <0x00200000 0x00400000>;
+		};
+		partition@600000 {
+			label = "nsystem";
+			reg = <0x00600000 0x00a00000>;
+		};
+		partition@1000000 {
+			label = "nrootfs";
+			reg = <0x01000000 0x03000000>;
+		};
+		partition@4000000 {
+			label = "ncustfs";
+			reg = <0x04000000 0x3c000000>;
+		};
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_sel>;
+	nand_sel: nand_sel {
+		function = "nand";
+		groups = "nand_grp";
+	};
+};
+
+&qspi {
+	status = "okay";
+	bspi-sel = <0>;
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		reg = <0x0>;
+		spi-max-frequency = <12500000>;
+		m25p,fast-read;
+		spi-cpol;
+		spi-cpha;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x000a0000>;
+		};
+
+		partition@a0000 {
+			label = "env";
+			reg = <0x000a0000 0x00060000>;
+		};
+
+		partition@100000 {
+			label = "system";
+			reg = <0x00100000 0x00600000>;
+		};
+
+		partition@700000 {
+			label = "rootfs";
+			reg = <0x00700000 0x01900000>;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
+
+&srab {
+	compatible = "brcm,bcm58522-srab", "brcm,nsp-srab";
+};
diff --git a/src/arm/broadcom/bcm958525er.dts b/src/arm/broadcom/bcm958525er.dts
new file mode 100644
index 0000000..9b9c225
--- /dev/null
+++ b/src/arm/broadcom/bcm958525er.dts
@@ -0,0 +1,197 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-nsp.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "NorthStar Plus SVK (BCM958525ER)";
+	compatible = "brcm,bcm958525er", "brcm,bcm58525", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+		open-source;
+		priority = <200>;
+	};
+};
+
+/* USB 3 support needed to be complete */
+
+&dma {
+	status = "okay";
+};
+
+&amac0 {
+	status = "okay";
+};
+
+&amac1 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&nand_controller {
+	nand@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+
+		partition@0 {
+			label = "nboot";
+			reg = <0x00000000 0x00200000>;
+			read-only;
+		};
+		partition@200000 {
+			label = "nenv";
+			reg = <0x00200000 0x00400000>;
+		};
+		partition@600000 {
+			label = "nsystem";
+			reg = <0x00600000 0x00a00000>;
+		};
+		partition@1000000 {
+			label = "nrootfs";
+			reg = <0x01000000 0x03000000>;
+		};
+		partition@4000000 {
+			label = "ncustfs";
+			reg = <0x04000000 0x3c000000>;
+		};
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_sel>;
+	nand_sel: nand_sel {
+		function = "nand";
+		groups = "nand_grp";
+	};
+};
+
+&qspi {
+	status = "okay";
+	bspi-sel = <0>;
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		reg = <0x0>;
+		spi-max-frequency = <12500000>;
+		m25p,fast-read;
+		spi-cpol;
+		spi-cpha;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x000a0000>;
+		};
+
+		partition@a0000 {
+			label = "env";
+			reg = <0x000a0000 0x00060000>;
+		};
+
+		partition@100000 {
+			label = "system";
+			reg = <0x00100000 0x00600000>;
+		};
+
+		partition@700000 {
+			label = "rootfs";
+			reg = <0x00700000 0x01900000>;
+		};
+	};
+};
+
+&sata_phy0 {
+	status = "okay";
+};
+
+&sata_phy1 {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
+
+&srab {
+	compatible = "brcm,bcm58525-srab", "brcm,nsp-srab";
+};
diff --git a/src/arm/broadcom/bcm958525xmc.dts b/src/arm/broadcom/bcm958525xmc.dts
new file mode 100644
index 0000000..ca93114
--- /dev/null
+++ b/src/arm/broadcom/bcm958525xmc.dts
@@ -0,0 +1,217 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-nsp.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "NorthStar Plus XMC (BCM958525xmc)";
+	compatible = "brcm,bcm958525xmc", "brcm,bcm58525", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x40000000>;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpioa 31 GPIO_ACTIVE_LOW>;
+		open-source;
+		priority = <200>;
+	};
+};
+
+/* XHCI support needed to be complete */
+
+&dma {
+	status = "okay";
+};
+
+&amac0 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	temperature-sensor@4c {
+		compatible = "adi,adt7461a";
+		reg = <0x4c>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
+
+	rtc@68 {
+		compatible = "st,m41t81";
+		reg = <0x68>;
+	};
+};
+
+&nand_controller {
+	nand@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+
+		partition@0 {
+			label = "nboot";
+			reg = <0x00000000 0x00200000>;
+			read-only;
+		};
+		partition@200000 {
+			label = "nenv";
+			reg = <0x00200000 0x00400000>;
+		};
+		partition@600000 {
+			label = "nsystem";
+			reg = <0x00600000 0x00a00000>;
+		};
+		partition@1000000 {
+			label = "nrootfs";
+			reg = <0x01000000 0x03000000>;
+		};
+		partition@4000000 {
+			label = "ncustfs";
+			reg = <0x04000000 0x3c000000>;
+		};
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_sel>;
+	nand_sel: nand_sel {
+		function = "nand";
+		groups = "nand_grp";
+	};
+};
+
+&qspi {
+	status = "okay";
+	bspi-sel = <0>;
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		reg = <0x0>;
+		spi-max-frequency = <12500000>;
+		m25p,fast-read;
+		spi-cpol;
+		spi-cpha;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x000a0000>;
+		};
+
+		partition@a0000 {
+			label = "env";
+			reg = <0x000a0000 0x00060000>;
+		};
+
+		partition@100000 {
+			label = "system";
+			reg = <0x00100000 0x00600000>;
+		};
+
+		partition@700000 {
+			label = "rootfs";
+			reg = <0x00700000 0x01900000>;
+		};
+	};
+};
+
+&sata_phy0 {
+	status = "okay";
+};
+
+&sata_phy1 {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&sdio {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
+
+&srab {
+	compatible = "brcm,bcm58525-srab", "brcm,nsp-srab";
+};
diff --git a/src/arm/broadcom/bcm958622hr.dts b/src/arm/broadcom/bcm958622hr.dts
new file mode 100644
index 0000000..9db3c85
--- /dev/null
+++ b/src/arm/broadcom/bcm958622hr.dts
@@ -0,0 +1,227 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-nsp.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "NorthStar Plus SVK (BCM958622HR)";
+	compatible = "brcm,bcm958622hr", "brcm,bcm58622", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+		open-source;
+		priority = <200>;
+	};
+};
+
+/* USB 3 and SLIC support needed to be complete */
+
+&dma {
+	status = "okay";
+};
+
+&amac0 {
+	status = "okay";
+};
+
+&amac1 {
+	status = "okay";
+};
+
+&amac2 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&nand_controller {
+	nand@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+
+		partition@0 {
+			label = "nboot";
+			reg = <0x00000000 0x00200000>;
+			read-only;
+		};
+		partition@200000 {
+			label = "nenv";
+			reg = <0x00200000 0x00400000>;
+		};
+		partition@600000 {
+			label = "nsystem";
+			reg = <0x00600000 0x00a00000>;
+		};
+		partition@1000000 {
+			label = "nrootfs";
+			reg = <0x01000000 0x03000000>;
+		};
+		partition@4000000 {
+			label = "ncustfs";
+			reg = <0x04000000 0x3c000000>;
+		};
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_sel>;
+	nand_sel: nand_sel {
+		function = "nand";
+		groups = "nand_grp";
+	};
+};
+
+&qspi {
+	status = "okay";
+	bspi-sel = <0>;
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		reg = <0x0>;
+		spi-max-frequency = <12500000>;
+		m25p,fast-read;
+		spi-cpol;
+		spi-cpha;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x000a0000>;
+		};
+
+		partition@a0000 {
+			label = "env";
+			reg = <0x000a0000 0x00060000>;
+		};
+
+		partition@100000 {
+			label = "system";
+			reg = <0x00100000 0x00600000>;
+		};
+
+		partition@700000 {
+			label = "rootfs";
+			reg = <0x00700000 0x01900000>;
+		};
+	};
+};
+
+&srab {
+	compatible = "brcm,bcm58622-srab", "brcm,nsp-srab";
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "port0";
+			reg = <0>;
+		};
+
+		port@1 {
+			label = "port1";
+			reg = <1>;
+		};
+
+		port@2 {
+			label = "port2";
+			reg = <2>;
+		};
+
+		port@3 {
+			label = "port3";
+			reg = <3>;
+		};
+
+		port@4 {
+			label = "port4";
+			reg = <4>;
+		};
+
+		port@8 {
+			ethernet = <&amac2>;
+			label = "cpu";
+			reg = <8>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm958623hr.dts b/src/arm/broadcom/bcm958623hr.dts
new file mode 100644
index 0000000..32786e7
--- /dev/null
+++ b/src/arm/broadcom/bcm958623hr.dts
@@ -0,0 +1,231 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-nsp.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "NorthStar Plus SVK (BCM958623HR)";
+	compatible = "brcm,bcm958623hr", "brcm,bcm58623", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+		open-source;
+		priority = <200>;
+	};
+};
+
+/* USB 3 and SLIC support needed to be complete */
+
+&dma {
+	status = "okay";
+};
+
+&amac0 {
+	status = "okay";
+};
+
+&amac1 {
+	status = "okay";
+};
+
+&amac2 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&nand_controller {
+	nand@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+
+		partition@0 {
+			label = "nboot";
+			reg = <0x00000000 0x00200000>;
+			read-only;
+		};
+		partition@200000 {
+			label = "nenv";
+			reg = <0x00200000 0x00400000>;
+		};
+		partition@600000 {
+			label = "nsystem";
+			reg = <0x00600000 0x00a00000>;
+		};
+		partition@1000000 {
+			label = "nrootfs";
+			reg = <0x01000000 0x03000000>;
+		};
+		partition@4000000 {
+			label = "ncustfs";
+			reg = <0x04000000 0x3c000000>;
+		};
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_sel>;
+	nand_sel: nand_sel {
+		function = "nand";
+		groups = "nand_grp";
+	};
+};
+
+&sata_phy0 {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+	bspi-sel = <0>;
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		reg = <0x0>;
+		spi-max-frequency = <12500000>;
+		m25p,fast-read;
+		spi-cpol;
+		spi-cpha;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x000a0000>;
+		};
+
+		partition@a0000 {
+			label = "env";
+			reg = <0x000a0000 0x00060000>;
+		};
+
+		partition@100000 {
+			label = "system";
+			reg = <0x00100000 0x00600000>;
+		};
+
+		partition@700000 {
+			label = "rootfs";
+			reg = <0x00700000 0x01900000>;
+		};
+	};
+};
+
+&srab {
+	compatible = "brcm,bcm58623-srab", "brcm,nsp-srab";
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "port0";
+			reg = <0>;
+		};
+
+		port@1 {
+			label = "port1";
+			reg = <1>;
+		};
+
+		port@2 {
+			label = "port2";
+			reg = <2>;
+		};
+
+		port@3 {
+			label = "port3";
+			reg = <3>;
+		};
+
+		port@4 {
+			label = "port4";
+			reg = <4>;
+		};
+
+		port@8 {
+			ethernet = <&amac2>;
+			label = "cpu";
+			reg = <8>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm958625-meraki-alamo.dtsi b/src/arm/broadcom/bcm958625-meraki-alamo.dtsi
new file mode 100644
index 0000000..c54451d
--- /dev/null
+++ b/src/arm/broadcom/bcm958625-meraki-alamo.dtsi
@@ -0,0 +1,284 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX65 series (Alamo).
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+#include "bcm958625-meraki-mx6x-common.dtsi"
+
+/ {
+	keys {
+		compatible = "gpio-keys-polled";
+		autorepeat;
+		poll-interval = <20>;
+
+		button-reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpioa 8 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			/* green:wan1-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <0>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 25 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			/* green:wan1-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 24 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2 {
+			/* green:wan2-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 27 GPIO_ACTIVE_LOW>;
+		};
+
+		led-3 {
+			/* green:wan2-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <3>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 26 GPIO_ACTIVE_LOW>;
+		};
+
+		led-4 {
+			/* amber:power */
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&gpioa 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5 {
+			/* white:status */
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpioa 31 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&axi {
+	mdio-mux@3f1c0 {
+		compatible = "mdio-mux-mmioreg", "mdio-mux";
+		reg = <0x3f1c0 0x4>;
+		mux-mask = <0x2000>;
+		mdio-parent-bus = <&mdio_ext>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio@0 {
+			reg = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			phy_port6: phy@0 {
+				reg = <0>;
+			};
+
+			phy_port7: phy@1 {
+				reg = <1>;
+			};
+
+			phy_port8: phy@2 {
+				reg = <2>;
+			};
+
+			phy_port9: phy@3 {
+				reg = <3>;
+			};
+
+			phy_port10: phy@4 {
+				reg = <4>;
+			};
+
+			switch@10 {
+				compatible = "qca,qca8337";
+				reg = <0x10>;
+				dsa,member = <1 0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					port@0 {
+						reg = <0>;
+						ethernet = <&sgmii1>;
+						phy-mode = "sgmii";
+						qca,sgmii-enable-pll;
+						qca,sgmii-txclk-falling-edge;
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						label = "lan8";
+						phy-handle = <&phy_port6>;
+					};
+
+					port@2 {
+						reg = <2>;
+						label = "lan9";
+						phy-handle = <&phy_port7>;
+					};
+
+					port@3 {
+						reg = <3>;
+						label = "lan10";
+						phy-handle = <&phy_port8>;
+					};
+
+					port@4 {
+						reg = <4>;
+						label = "lan11";
+						phy-handle = <&phy_port9>;
+					};
+
+					port@5 {
+						reg = <5>;
+						label = "lan12";
+						phy-handle = <&phy_port10>;
+					};
+				};
+			};
+		};
+
+		mdio-mii@2000 {
+			reg = <0x2000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			phy_port1: phy@0 {
+				reg = <0>;
+			};
+
+			phy_port2: phy@1 {
+				reg = <1>;
+			};
+
+			phy_port3: phy@2 {
+				reg = <2>;
+			};
+
+			phy_port4: phy@3 {
+				reg = <3>;
+			};
+
+			phy_port5: phy@4 {
+				reg = <4>;
+			};
+
+			switch@10 {
+				compatible = "qca,qca8337";
+				reg = <0x10>;
+				dsa,member = <2 0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					port@0 {
+						reg = <0>;
+						ethernet = <&sgmii0>;
+						phy-mode = "sgmii";
+						qca,sgmii-enable-pll;
+						qca,sgmii-txclk-falling-edge;
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						label = "lan3";
+						phy-handle = <&phy_port1>;
+					};
+
+					port@2 {
+						reg = <2>;
+						label = "lan4";
+						phy-handle = <&phy_port2>;
+					};
+
+					port@3 {
+						reg = <3>;
+						label = "lan5";
+						phy-handle = <&phy_port3>;
+					};
+
+					port@4 {
+						reg = <4>;
+						label = "lan6";
+						phy-handle = <&phy_port4>;
+					};
+
+					port@5 {
+						reg = <5>;
+						label = "lan7";
+						phy-handle = <&phy_port5>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&srab {
+	compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
+	status = "okay";
+	dsa,member = <0 0>;
+
+	ports {
+		port@0 {
+			label = "wan1";
+			reg = <0>;
+		};
+
+		port@1 {
+			label = "wan2";
+			reg = <1>;
+		};
+
+		sgmii0: port@4 {
+			label = "sw0";
+			reg = <4>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		sgmii1: port@5 {
+			label = "sw1";
+			reg = <5>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@8 {
+			ethernet = <&amac2>;
+			reg = <8>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm958625-meraki-kingpin.dtsi b/src/arm/broadcom/bcm958625-meraki-kingpin.dtsi
new file mode 100644
index 0000000..1830844
--- /dev/null
+++ b/src/arm/broadcom/bcm958625-meraki-kingpin.dtsi
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX64 series (Kingpin).
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+#include "bcm958625-meraki-mx6x-common.dtsi"
+
+/ {
+
+	keys {
+		compatible = "gpio-keys-polled";
+		autorepeat;
+		poll-interval = <20>;
+
+		button-reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpioa 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			/* green:lan1-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <0>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 19 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			/* green:lan1-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 18 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2 {
+			/* green:lan2-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 24 GPIO_ACTIVE_LOW>;
+		};
+
+		led-3 {
+			/* green:lan2-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <3>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 20 GPIO_ACTIVE_LOW>;
+		};
+
+		led-4 {
+			/* green:lan3-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <4>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 26 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5 {
+			/* green:lan3-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <5>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 25 GPIO_ACTIVE_LOW>;
+		};
+
+		led-6 {
+			/* green:lan4-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 28 GPIO_ACTIVE_LOW>;
+		};
+
+		led-7 {
+			/* green:lan4-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <7>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 27 GPIO_ACTIVE_LOW>;
+		};
+
+		led-8 {
+			/* green:wan-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <8>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 30 GPIO_ACTIVE_LOW>;
+		};
+
+		led-9 {
+			/* green:wan-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <9>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 29 GPIO_ACTIVE_LOW>;
+		};
+
+		led-a {
+			/* amber:power */
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&gpioa 0 GPIO_ACTIVE_LOW>;
+		};
+
+		led-b {
+			/* white:status */
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpioa 31 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&srab {
+	compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+			reg = <0>;
+		};
+
+		port@1 {
+			label = "lan2";
+			reg = <1>;
+		};
+
+		port@2 {
+			label = "lan3";
+			reg = <2>;
+		};
+
+		port@3 {
+			label = "lan4";
+			reg = <3>;
+		};
+
+		port@4 {
+			label = "wan";
+			reg = <4>;
+		};
+
+		port@8 {
+			ethernet = <&amac2>;
+			reg = <8>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
diff --git a/src/arm/broadcom/bcm958625-meraki-mx64-a0.dts b/src/arm/broadcom/bcm958625-meraki-mx64-a0.dts
new file mode 100644
index 0000000..9944566
--- /dev/null
+++ b/src/arm/broadcom/bcm958625-meraki-mx64-a0.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX64 with A0 SoC.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm958625-meraki-kingpin.dtsi"
+#include "bcm-nsp-ax.dtsi"
+
+/ {
+	model = "Cisco Meraki MX64(A0)";
+	compatible = "meraki,mx64-a0", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
diff --git a/src/arm/broadcom/bcm958625-meraki-mx64.dts b/src/arm/broadcom/bcm958625-meraki-mx64.dts
new file mode 100644
index 0000000..0693943
--- /dev/null
+++ b/src/arm/broadcom/bcm958625-meraki-mx64.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX64 with B0+ SoC.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm958625-meraki-kingpin.dtsi"
+
+/ {
+	model = "Cisco Meraki MX64";
+	compatible = "meraki,mx64", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
diff --git a/src/arm/broadcom/bcm958625-meraki-mx64w-a0.dts b/src/arm/broadcom/bcm958625-meraki-mx64w-a0.dts
new file mode 100644
index 0000000..112fddb
--- /dev/null
+++ b/src/arm/broadcom/bcm958625-meraki-mx64w-a0.dts
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX64W with A0 SoC.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm958625-meraki-kingpin.dtsi"
+#include "bcm-nsp-ax.dtsi"
+
+/ {
+	model = "Cisco Meraki MX64W(A0)";
+	compatible = "meraki,mx64w-a0", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm958625-meraki-mx64w.dts b/src/arm/broadcom/bcm958625-meraki-mx64w.dts
new file mode 100644
index 0000000..de2e367
--- /dev/null
+++ b/src/arm/broadcom/bcm958625-meraki-mx64w.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX64W with B0+ SoC.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm958625-meraki-kingpin.dtsi"
+
+/ {
+	model = "Cisco Meraki MX64W";
+	compatible = "meraki,mx64w", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm958625-meraki-mx65.dts b/src/arm/broadcom/bcm958625-meraki-mx65.dts
new file mode 100644
index 0000000..d1b684d
--- /dev/null
+++ b/src/arm/broadcom/bcm958625-meraki-mx65.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX65.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm958625-meraki-alamo.dtsi"
+
+/ {
+	model = "Cisco Meraki MX65";
+	compatible = "meraki,mx65", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
diff --git a/src/arm/broadcom/bcm958625-meraki-mx65w.dts b/src/arm/broadcom/bcm958625-meraki-mx65w.dts
new file mode 100644
index 0000000..a2165ab
--- /dev/null
+++ b/src/arm/broadcom/bcm958625-meraki-mx65w.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX65W.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm958625-meraki-alamo.dtsi"
+
+/ {
+	model = "Cisco Meraki MX65W";
+	compatible = "meraki,mx65w", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm958625-meraki-mx6x-common.dtsi b/src/arm/broadcom/bcm958625-meraki-mx6x-common.dtsi
new file mode 100644
index 0000000..b0854d8
--- /dev/null
+++ b/src/arm/broadcom/bcm958625-meraki-mx6x-common.dtsi
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Common Bindings for Cisco Meraki MX64 (Kingpin) and MX65 (Alamo) devices.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+#include "bcm-nsp.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	pwm-leds {
+		compatible = "pwm-leds";
+
+		led-1 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_RED>;
+			pwms = <&pwm 1 50000>;
+			max-brightness = <255>;
+		};
+
+		led-2 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+			pwms = <&pwm 2 50000>;
+			max-brightness = <255>;
+		};
+
+		led-3 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_BLUE>;
+			pwms = <&pwm 3 50000>;
+			max-brightness = <255>;
+		};
+	};
+};
+
+&amac2 {
+	status = "okay";
+	nvmem-cells = <&mac_address>;
+	nvmem-cell-names = "mac-address";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		mac_address: mac-address@66 {
+			reg = <0x66 0x6>;
+		};
+	};
+};
+
+&nand_controller {
+	nand@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition@80000 {
+			label = "shmoo";
+			reg = <0x80000 0x80000>;
+			read-only;
+		};
+
+		partition@100000 {
+			label = "bootkernel1";
+			reg = <0x100000 0x300000>;
+		};
+
+		partition@400000 {
+			label = "nvram";
+			reg = <0x400000 0x100000>;
+		};
+
+		partition@500000 {
+			label = "bootkernel2";
+			reg = <0x500000 0x300000>;
+		};
+
+		partition@800000 {
+			label = "ubi";
+			reg = <0x800000 0x3f700000>;
+		};
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm_leds>;
+
+	pwm_leds: pwm_leds {
+		function = "pwm";
+		groups = "pwm1_grp", "pwm2_grp", "pwm3_grp";
+	};
+};
+
+&pwm {
+	status = "okay";
+	#pwm-cells = <2>;
+};
+
+&uart0 {
+	clock-frequency = <62500000>;
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm958625hr.dts b/src/arm/broadcom/bcm958625hr.dts
new file mode 100644
index 0000000..74263d9
--- /dev/null
+++ b/src/arm/broadcom/bcm958625hr.dts
@@ -0,0 +1,254 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-nsp.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "NorthStar Plus SVK (BCM958625HR)";
+	compatible = "brcm,bcm958625hr", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x20000000>;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+		open-source;
+		priority = <200>;
+	};
+
+	sfp: sfp {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c0>;
+		mod-def0-gpios = <&gpioa 28 GPIO_ACTIVE_LOW>;
+		los-gpios = <&gpioa 24 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&gpioa 30 GPIO_ACTIVE_HIGH>;
+		tx-disable-gpios = <&gpioa 26 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&dma {
+	status = "okay";
+};
+
+&amac0 {
+	status = "okay";
+};
+
+&amac1 {
+	status = "okay";
+};
+
+&amac2 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&nand_controller {
+	nand@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+
+		partition@0 {
+			label = "nboot";
+			reg = <0x00000000 0x00200000>;
+			read-only;
+		};
+		partition@200000 {
+			label = "nenv";
+			reg = <0x00200000 0x00400000>;
+		};
+		partition@600000 {
+			label = "nsystem";
+			reg = <0x00600000 0x00a00000>;
+		};
+		partition@1000000 {
+			label = "nrootfs";
+			reg = <0x01000000 0x03000000>;
+		};
+		partition@4000000 {
+			label = "ncustfs";
+			reg = <0x04000000 0x3c000000>;
+		};
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_sel>;
+	nand_sel: nand_sel {
+		function = "nand";
+		groups = "nand_grp";
+	};
+};
+
+&qspi {
+	status = "okay";
+	bspi-sel = <0>;
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		reg = <0x0>;
+		spi-max-frequency = <12500000>;
+		m25p,fast-read;
+		spi-cpol;
+		spi-cpha;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x000a0000>;
+		};
+
+		partition@a0000 {
+			label = "env";
+			reg = <0x000a0000 0x00060000>;
+		};
+
+		partition@100000 {
+			label = "system";
+			reg = <0x00100000 0x00600000>;
+		};
+
+		partition@700000 {
+			label = "rootfs";
+			reg = <0x00700000 0x01900000>;
+		};
+	};
+};
+
+&sata_phy0 {
+	status = "okay";
+};
+
+&sata_phy1 {
+	status = "okay";
+};
+
+&srab {
+	compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "port0";
+			reg = <0>;
+		};
+
+		port@1 {
+			label = "port1";
+			reg = <1>;
+		};
+
+		port@2 {
+			label = "port2";
+			reg = <2>;
+		};
+
+		port@3 {
+			label = "port3";
+			reg = <3>;
+		};
+
+		port@4 {
+			label = "port4";
+			reg = <4>;
+		};
+
+		port@5 {
+			label = "sfp";
+			phy-mode = "sgmii";
+			reg = <5>;
+			sfp = <&sfp>;
+			managed = "in-band-status";
+		};
+
+		port@8 {
+			ethernet = <&amac2>;
+			label = "cpu";
+			reg = <8>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm958625k.dts b/src/arm/broadcom/bcm958625k.dts
new file mode 100644
index 0000000..69ebc7a
--- /dev/null
+++ b/src/arm/broadcom/bcm958625k.dts
@@ -0,0 +1,271 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2015 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-nsp.dtsi"
+
+/ {
+	model = "NorthStar Plus SVK (BCM958625K)";
+	compatible = "brcm,bcm958625k", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
+
+&dma {
+	status = "okay";
+};
+
+&amac0 {
+	status = "okay";
+};
+
+&amac1 {
+	status = "okay";
+};
+
+&amac2 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&nand_controller {
+	nand@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+
+		partition@0 {
+			label = "nboot";
+			reg = <0x00000000 0x00200000>;
+			read-only;
+		};
+		partition@200000 {
+			label = "nenv";
+			reg = <0x00200000 0x00400000>;
+		};
+		partition@600000 {
+			label = "nsystem";
+			reg = <0x00600000 0x00a00000>;
+		};
+		partition@1000000 {
+			label = "nrootfs";
+			reg = <0x01000000 0x03000000>;
+		};
+		partition@4000000 {
+			label = "ncustfs";
+			reg = <0x04000000 0x3c000000>;
+		};
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pcie2 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_sel>, <&gpiobs>, <&pwmc>;
+
+	nand_sel: nand_sel {
+		function = "nand";
+		groups = "nand_grp";
+	};
+
+	gpiobs: gpiobs {
+		function = "gpio_b";
+		groups = "gpio_b_0_grp", "gpio_b_1_grp", "gpio_b_2_grp",
+			 "gpio_b_3_grp";
+	};
+
+	pwmc: pwmc {
+		function = "pwm";
+		groups = "pwm0_grp", "pwm1_grp", "pwm2_grp", "pwm3_grp";
+	};
+
+	emmc_sel: emmc_sel {
+		function = "emmc";
+		groups = "emmc_grp";
+	};
+};
+
+&pwm {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+	bspi-sel = <0>;
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		reg = <0x0>;
+		spi-max-frequency = <12500000>;
+		m25p,fast-read;
+		spi-cpol;
+		spi-cpha;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x000a0000>;
+		};
+
+		partition@a0000 {
+			label = "env";
+			reg = <0x000a0000 0x00060000>;
+		};
+
+		partition@100000 {
+			label = "system";
+			reg = <0x00100000 0x00600000>;
+		};
+
+		partition@700000 {
+			label = "rootfs";
+			reg = <0x00700000 0x01900000>;
+		};
+	};
+};
+
+&sata_phy0 {
+	status = "okay";
+};
+
+&sata_phy1 {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+/*
+ * By default the sd slot is functional. For emmc to work add "<&emmc_sel>"
+ * and delete "<&nand_sel>" in "pinctrl-0" property of pinctrl node. Remove the
+ * bus-width property here and disable the nand node with status = "disabled";.
+ *
+ * Ex: pinctrl-0 = <&emmc_sel>, <&gpiobs>, <&pwmc>;
+ */
+&sdio {
+	bus-width = <4>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&srab {
+	compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "port0";
+			reg = <0>;
+		};
+
+		port@1 {
+			label = "port1";
+			reg = <1>;
+		};
+
+		port@2 {
+			label = "port2";
+			reg = <2>;
+		};
+
+		port@3 {
+			label = "port3";
+			reg = <3>;
+		};
+
+		port@4 {
+			label = "port4";
+			reg = <4>;
+		};
+
+		port@8 {
+			ethernet = <&amac2>;
+			label = "cpu";
+			reg = <8>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm963138.dts b/src/arm/broadcom/bcm963138.dts
new file mode 100644
index 0000000..1b405c2
--- /dev/null
+++ b/src/arm/broadcom/bcm963138.dts
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63138.dtsi"
+
+/ {
+	model = "Broadcom BCM963138 Reference Board";
+	compatible = "brcm,bcm963138", "brcm,bcm63138", "brcm,bcmbca";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &serial0;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm963138dvt.dts b/src/arm/broadcom/bcm963138dvt.dts
new file mode 100644
index 0000000..b5af618
--- /dev/null
+++ b/src/arm/broadcom/bcm963138dvt.dts
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Broadcom BCM63138 Reference Board DTS
+ */
+
+/dts-v1/;
+
+#include "bcm63138.dtsi"
+
+/ {
+	compatible = "brcm,BCM963138DVT", "brcm,bcm63138", "brcm,bcmbca";
+	model = "Broadcom BCM963138DVT";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &serial0;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&serial1 {
+	status = "okay";
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		brcm,nand-oob-sectors-size = <16>;
+	};
+};
+
+&ahci {
+	status = "okay";
+};
+
+&sata_phy {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm963148.dts b/src/arm/broadcom/bcm963148.dts
new file mode 100644
index 0000000..1f5d6d7
--- /dev/null
+++ b/src/arm/broadcom/bcm963148.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63148.dtsi"
+
+/ {
+	model = "Broadcom BCM963148 Reference Board";
+	compatible = "brcm,bcm963148", "brcm,bcm63148", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm963178.dts b/src/arm/broadcom/bcm963178.dts
new file mode 100644
index 0000000..d036e99
--- /dev/null
+++ b/src/arm/broadcom/bcm963178.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63178.dtsi"
+
+/ {
+	model = "Broadcom BCM963178 Reference Board";
+	compatible = "brcm,bcm963178", "brcm,bcm63178", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm96756.dts b/src/arm/broadcom/bcm96756.dts
new file mode 100644
index 0000000..8b104f3
--- /dev/null
+++ b/src/arm/broadcom/bcm96756.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6756.dtsi"
+
+/ {
+	model = "Broadcom BCM96756 Reference Board";
+	compatible = "brcm,bcm96756", "brcm,bcm6756", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm96846.dts b/src/arm/broadcom/bcm96846.dts
new file mode 100644
index 0000000..55852c2
--- /dev/null
+++ b/src/arm/broadcom/bcm96846.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6846.dtsi"
+
+/ {
+	model = "Broadcom BCM96846 Reference Board";
+	compatible = "brcm,bcm96846", "brcm,bcm6846", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm96855.dts b/src/arm/broadcom/bcm96855.dts
new file mode 100644
index 0000000..2ad880a
--- /dev/null
+++ b/src/arm/broadcom/bcm96855.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6855.dtsi"
+
+/ {
+	model = "Broadcom BCM96855 Reference Board";
+	compatible = "brcm,bcm96855", "brcm,bcm6855", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm96878.dts b/src/arm/broadcom/bcm96878.dts
new file mode 100644
index 0000000..b7af8ad
--- /dev/null
+++ b/src/arm/broadcom/bcm96878.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6878.dtsi"
+
+/ {
+	model = "Broadcom BCM96878 Reference Board";
+	compatible = "brcm,bcm96878", "brcm,bcm6878", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm988312hr.dts b/src/arm/broadcom/bcm988312hr.dts
new file mode 100644
index 0000000..e96bc3f
--- /dev/null
+++ b/src/arm/broadcom/bcm988312hr.dts
@@ -0,0 +1,231 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "bcm-nsp.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "NorthStar Plus SVK (BCM988312HR)";
+	compatible = "brcm,bcm988312hr", "brcm,bcm88312", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+		open-source;
+		priority = <200>;
+	};
+};
+
+/* USB 3 support needed to be complete */
+
+&dma {
+	status = "okay";
+};
+
+&amac0 {
+	status = "okay";
+};
+
+&amac1 {
+	status = "okay";
+};
+
+&amac2 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&nand_controller {
+	nand@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+
+		partition@0 {
+			label = "nboot";
+			reg = <0x00000000 0x00200000>;
+			read-only;
+		};
+		partition@200000 {
+			label = "nenv";
+			reg = <0x00200000 0x00400000>;
+		};
+		partition@600000 {
+			label = "nsystem";
+			reg = <0x00600000 0x00a00000>;
+		};
+		partition@1000000 {
+			label = "nrootfs";
+			reg = <0x01000000 0x03000000>;
+		};
+		partition@4000000 {
+			label = "ncustfs";
+			reg = <0x04000000 0x3c000000>;
+		};
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_sel>;
+	nand_sel: nand_sel {
+		function = "nand";
+		groups = "nand_grp";
+	};
+};
+
+&qspi {
+	status = "okay";
+	bspi-sel = <0>;
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		reg = <0x0>;
+		spi-max-frequency = <12500000>;
+		m25p,fast-read;
+		spi-cpol;
+		spi-cpha;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x000a0000>;
+		};
+
+		partition@a0000 {
+			label = "env";
+			reg = <0x000a0000 0x00060000>;
+		};
+
+		partition@100000 {
+			label = "system";
+			reg = <0x00100000 0x00600000>;
+		};
+
+		partition@700000 {
+			label = "rootfs";
+			reg = <0x00700000 0x01900000>;
+		};
+	};
+};
+
+&sata_phy0 {
+	status = "okay";
+};
+
+&sata_phy1 {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&srab {
+	compatible = "brcm,bcm88312-srab", "brcm,nsp-srab";
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "port0";
+			reg = <0>;
+		};
+
+		port@1 {
+			label = "port1";
+			reg = <1>;
+		};
+
+		port@2 {
+			label = "port2";
+			reg = <2>;
+		};
+
+		port@3 {
+			label = "port3";
+			reg = <3>;
+		};
+
+		port@4 {
+			label = "port4";
+			reg = <4>;
+		};
+
+		port@8 {
+			ethernet = <&amac2>;
+			label = "cpu";
+			reg = <8>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/src/arm/broadcom/bcm9hmidc.dtsi b/src/arm/broadcom/bcm9hmidc.dtsi
new file mode 100644
index 0000000..65397c0
--- /dev/null
+++ b/src/arm/broadcom/bcm9hmidc.dtsi
@@ -0,0 +1,42 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2015 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/*
+ * Broadcom human machine interface daughter card (bcm9hmidc) installed on
+ * bcm958300k/bcm958305k boards
+ */
+
+&touchscreen {
+	touchscreen-inverted-x;
+	touchscreen-inverted-y;
+	status = "okay";
+};